Get yourself an Quilified Electrician, The wire for the 100 amp fuse is going to be larger than what it would take for a 60 amp fuse so the wires are not going too fit in the 60 amp fuse properly Danger in more ways than one.
60 Hz in North America, 50 Hz in Europe.
Most jurisdictions will no longer allow the installation of 60 amp main service panels. If you are doing a repair, and a simple replacement MIGHT be considered a repair, you might get away with replacing one with the other. But if you have the time, money, and/or you KNOW WHAT YOU ARE DOING, I suggest you upgrade the service to at least 100 amps. Even in small homes the typical installation is now 125 amps. And if the home is all electric, typical installation is 200amps. Replacing a service panel can be very dangerous. Do this ONLY if you know what you are doing and how to protect yourself from injury. If you are guessing, DO NOT DO THIS TASK.
As long as the voltages match a 60 amp service will handle a 700 watt microwave. The microwave will only draw A = W/V, A = 700/120 = 5.8 amps.
A 200 amp service panel with a 60 amp sub-panel.
Mine and many that I've seen are 100 amp . I've seen one or two that are 60 amp, but they were pre -'75.
You can install a 100 amp sub panel off a 60 amp main panel fed by 100 amp service. This allows for the sub panel to be adequately powered with headroom for future circuits or expansions. It is important to ensure the wire size from the main panel to the sub panel is sufficient to handle the load.
It depends on your electricity needs. If you are adding more appliances or equipment that require higher power usage, upgrading to 100 amp service may be necessary to meet the increased demand. It is recommended to consult with a licensed electrician to assess your specific requirements before making a decision.
60 Hz in North America, 50 Hz in Europe.
The recommended wire size for a 60 amp service is typically 6-gauge copper wire.
Most jurisdictions will no longer allow the installation of 60 amp main service panels. If you are doing a repair, and a simple replacement MIGHT be considered a repair, you might get away with replacing one with the other. But if you have the time, money, and/or you KNOW WHAT YOU ARE DOING, I suggest you upgrade the service to at least 100 amps. Even in small homes the typical installation is now 125 amps. And if the home is all electric, typical installation is 200amps. Replacing a service panel can be very dangerous. Do this ONLY if you know what you are doing and how to protect yourself from injury. If you are guessing, DO NOT DO THIS TASK.
Without knowing the sq. ft. area of your house and what appliances you have connected and if your hot water tank is electric it is hard to make an assessment. The average household draws about 50 amps so if you are adding another 30 you will be getting close to the limit of the new panel. Ask for an estimate on the 100 amp panel and then on a 200 amp panel. The labor costs should not be much higher for the larger installation of a 200 amp panel just the materials.
Using a wire rated for 100 amps for a 60-amp circuit is generally fine. It's important to ensure that the wire gauge matches the amperage requirements to prevent overheating and potential fire hazards. Check local electrical codes to confirm that it is within regulations.
It is legal to buy a house with a 60 amp service, but it may limit the electrical capacity of the home. Check with local building codes and consult an electrician to determine if the service meets your needs and if an upgrade is recommended.
Hi, It really depends on when your home was built and whether or not you have an older home that had an upgrade at one time or another. For older homes, it was usually 60 amps and for the newer homes, it's usually 100 amp service. Most homes today have 100 amp service, but lately, the trend has been installing a higher amperage service, usually around 200 amps. All that means, is that you have that much power available, and of course, you're generally billed for what you use and not how large the available service is. Hope that helps, Cubby
Typically, responsibility for upgrading the service falls on the homeowner, unless specified otherwise in the purchase agreement. It's important to review the contract and consult a real estate attorney for guidance on seeking recourse from the seller if the service upgrade was misrepresented.
As long as the voltages match a 60 amp service will handle a 700 watt microwave. The microwave will only draw A = W/V, A = 700/120 = 5.8 amps.
I would recommend at least a 200 amp service. and a subpanel in the workshop. This is not a DIY project. Contact a qualified electrician. Well, I guess it depends how many arms you have ... I can only usually run one power tool at once, so it depends on if you have help or not. You could power New York City on a 100 amp service if you only light one 60 watt bulb at a time ...