0
What else can I help you with?
Did my dryer trip the breaker or vice versa when I turned the breaker back on but now the dryer won't work?
The dryer tripped the breaker. Have it repaired. Don't try to use it again. You could cause a fire.
Adding a 220 line to panel box for a dryer?
A dryer requires a 30 amp receptacle. This will be to receive a four blade dryer plug. The wire needed will be a three copper wire #10 cable set with a bare #14 copper ground wire. The breaker will be a two pole 30 amp breaker.
Can you have a gas dryer and a washing machine on the same dedicated 20 amp service?
An electrician would put in two separate circuits since there is no telling in future that gas dryer might be replaced. You need to look at the breaker protecting the circuit and see if the current from the dryer and washer when added together don't exceed 80% of the breaker rating. Also the start up current for the dryer tumbler and washing machine motor don't add up to more than the breaker rating when added together. This is where problems will occur since start up currents may be 6 times running current.
Is main breaker only powering one half of hot bus because when dryer is on some light on circuits on dead bus work?
Yes, it would appear that one side of the main is open at the fuse, breaker, drop conductors, or transformer.
What are the standard size circuit breaker amperages?
In North America the standard sizes for breakers are 15, 20, 30, and 40 amps. The 15 amp size breaker is used in general circuit wiring. The 20 amp size breaker is used for dedicated appliance receptacles, hot water tank and baseboard heating. The 30 amp size breaker is used for a clothes dryer. The 40 amp size breaker is used for the electric range.
What would happen if a 240V breaker was on and someone attempted to turn on the clothes dryer?
Don't understand this question. If the breaker is on, then the dryer would function normally, if the breaker your are referring to is the one for the dryer. If the breaker is off then no function. A dryer runs on 220.
What amperage does a 3 wire dryer require?
Answer for USA, Canada and countries running a 60 Hertz supply service.The breaker required for a dryer is a two pole 30 amp breaker which will feed a 3 conductor #10 cable.
Has the tripped circuit breaker affected the operation of your dryer?
Yes, the tripped circuit breaker has affected the operation of the dryer.
Did my dryer trip the breaker or vice versa when I turned the breaker back on but now the dryer won't work?
The dryer tripped the breaker. Have it repaired. Don't try to use it again. You could cause a fire.
If you install a 30A 240V GFI breaker will this be ok or will the cycles the dryer has prematurely fail the breaker?
Installing a 30A 240V GFI breaker for a dryer should be fine as long as the wiring and dryer itself are compatible with the breaker. The GFI breaker is designed to protect against electrical faults and should not be affected by the cycles of the dryer. Make sure to follow the installation instructions carefully to ensure proper functioning.
Why is my dryer outlet not working?
Your dryer outlet may not be working due to a tripped circuit breaker, a blown fuse, a faulty outlet, or a problem with the dryer itself. It is recommended to check these potential issues and consult a professional if needed.
How can I safely install a dryer with a high amp breaker?
To safely install a dryer with a high amp breaker, make sure to follow the manufacturer's instructions carefully, use the correct gauge wire for the amperage, and hire a licensed electrician if needed for proper installation.
Adding a 220 line to panel box for a dryer?
A dryer requires a 30 amp receptacle. This will be to receive a four blade dryer plug. The wire needed will be a three copper wire #10 cable set with a bare #14 copper ground wire. The breaker will be a two pole 30 amp breaker.
Does a dryer need a quick disconnect breaker?
A dryer does not require a quick disconnect breaker. However, it is recommended to have a dedicated circuit with a proper circuit breaker for the dryer to ensure safe operation and to meet building code requirements.
Why does my dryer breaker keep tripping?
Your dryer breaker may keep tripping due to an overload of electricity, a faulty breaker, a short circuit in the wiring, or a malfunctioning dryer component. It is important to have a professional electrician inspect and repair the issue to ensure safety and proper functioning of your dryer.
What is the recommended amperage for a breaker to use with a 30 amp dryer?
The recommended amperage for a breaker to use with a 30 amp dryer is 30 amps.
Why does your main circuit breaker trip when your dryer runs 15 minutes Is it because your vent needs to be cleaned?
Could be but you could also have a weak breaker that will no longer hold the load of your dryer. That is if your talking about your dryer breaker tripping. If your "main breaker" is tripping you have a different problem. Call an electrician in that case. A plugged up dryer shouldn't be tripping your main
