0
What size conduit and aluminum wire for a 400 foot run on a 120 240 volt system?
Wiki User
∙ 11y ago
The key parameter in sizing wire is the current requirement. Once you know that you can look up value in a wire gauge table. The length of the run is important for longer runs because of the resistance of the wire itself. Aluminum wire requires a larger diameter than copper for the same current. Once you calculate the wire size you can then size the conduit.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What size aluminum wire for a 220v 200a service in conduit undrreground at 180 ft?
250 MCM aluminum minimum
What does a 10 foot rigid metal conduit weigh?
depends on size....
Is it legal to support a conduit from another conduit of the same size?
No, the conduit has to be supported individually from a supportive structure. The spacing of the strapping is related to the size of the conduit.
What size should under ground conduit be from pole to meter base?
For new 200 amp services the conduit size should be 3 inch PVC.
What is the hole size required for a 2.5 conduit?
A trade size hole for a 2-1/2" EMT conduit connector, the hole needs to be 2-7/8" in diameter. A 3" rigid conduit can also use this size hole without the lock nuts falling into the hole.
What size aluminum wire for a 220v 200a service in conduit undrreground at 180 ft?
250 MCM aluminum minimum
What does a 10 foot rigid metal conduit weigh?
depends on size....
Is it legal to support a conduit from another conduit of the same size?
No, the conduit has to be supported individually from a supportive structure. The spacing of the strapping is related to the size of the conduit.
Can you list the different PVC conduit fittings?
ma - male adapter, fa - female adapter, coup - coupling, conn - connector, cap - end cap, reducer - bushings that reduce the size of a conduit to allow connection to a smaller size conduit, expansion joints - to allow the expansion and contraction in the conduit system.
What size conduit and aluminum wire for a 400 foot run for 200 amps?
For a 200 amp service over a 400 foot run, you would need to use at least a 2-inch conduit to accommodate the size of the aluminum wire required. You would typically use 3/0 aluminum wire for this setup to ensure efficient power transmission and meet code requirements for voltage drop. It's recommended to consult with a licensed electrician to determine the exact specifications for your specific setup.
What size conduit for 400 amp service?
4 inch rigid conduit
What size pipe and size aluminum wire are required for a 100A sub panel off a 200A main service?
For a 100A subpanel, a minimum of 1.5-inch Schedule 80 PVC conduit or 1.25-inch rigid metal conduit is recommended. As for the aluminum wire, for a 100A feeder, you would typically use 1/0 AWG aluminum wire for a 3-wire setup or 2/0 AWG aluminum wire for a 4-wire setup. Always consult local electrical codes and a licensed electrician for precise specifications for your installation.
What is the actual hole size for 1 inch conduit?
Actual hole size for 1 inch conduit is 1.362"
What size conduit is needed for wiring in Indian houses?
The size of conduit is based on the size of the wires in it. The size of the wires depends on the load connected in the house. Without these other two values an answer can not be given.
What size conduit for 200 amps?
120mm
What size should under ground conduit be from pole to meter base?
For new 200 amp services the conduit size should be 3 inch PVC.
What is the hole size required for a 2.5 conduit?
A trade size hole for a 2-1/2" EMT conduit connector, the hole needs to be 2-7/8" in diameter. A 3" rigid conduit can also use this size hole without the lock nuts falling into the hole.
