To answer this question a voltage is needed. I = 20/E.
<<>>
Each device powered by the transformer will have a rating of draw also in VA. So many for a t-stat, so many for zone valve or damper etc... add em up, make sure transformer is over and you re good. 20 VA is not very big. door bell Transformers are around that size. most hvac systems need 30, 50, 70 or more VA.
This typically has to do with how many amps you can safely pull from the secondary of the transformer.
It depends on how many amps it was designed for. A 12.5kV/600v 10kVA 3 phase transformer can handle ~.5 amps on the primary and ~10A on the secondary. A 600/120V 10kVA 3 phase transformer can handle ~10A on the primary and ~50 on the secondary.
The formula you are looking for is I = W/E. Amps = Watts/Volts.
There are actually three pieces to this puzzle - resistance. And you're missing that one.
for three phase the calculation is 30,000 = 1.73*V*I - simple as that. For single Phase the calculation is 30,000 = V*I - simple as that It is important to note the voltage in the first line is Line to Line (typically how it is specified in three phase power systems), and the second line it is Line to neutral. A 30KVA transformer is the same as 30,000VA to find out the Amps you need to divide the voltage if the transformer is single phase for example: 30,000VA / 480V = 62.5 Amps The calculation for a 3 phase transformer is the VA / voltage / 1.73 for example: 30,000VA /480V / 1.73 = 36.12 Amps
A transformer is a power source. It will provide voltage to a device. Find the voltage rating on the device, say 24V. 250/24 = ~10A.
You have not provide enough information. You don't explain what 0.05 references. You need to know the secondary voltage and resistance to calculate current.
This typically has to do with how many amps you can safely pull from the secondary of the transformer.
2.083 amps
The amps you can get from a 500 kVA transformer would depend on the voltage of the transformer's output. To calculate amperage, you can use the formula: Amps = Power (kVA) / Voltage. For example, if the output voltage is 480V, you would get approximately 1041 amps (500 kVA / 480V).
The transformer itself does not pull current. Whatever you connect to the transformer pulls current. Whatever the output voltage of the transformer is, divide that into 600 and you get maximum current possible without burning up the transformer. At 24V that's 25 amps.
It depends on how many amps it was designed for. A 12.5kV/600v 10kVA 3 phase transformer can handle ~.5 amps on the primary and ~10A on the secondary. A 600/120V 10kVA 3 phase transformer can handle ~10A on the primary and ~50 on the secondary.
It depends on the rated voltage of its secondary.
To calculate the amperage in the secondary side of a transformer, you can use the formula: Amps = kVA / (Volts x Sqrt(3)). For a 250 kVA transformer with a 220-volt secondary, the amperage will be approximately 660.4 Amps.
The formula you are looking for is I = W/E. Amps = Watts/Volts.
Rephrase your question, as it doesn't make any sense. If the primary side of the transformer is 480 volts 3 phase, this transformer can be supplied from a breaker as big as 180 amps. If 480 volts 3 phase is your secondary then you can supply up to 180 amps to your loads.
The primary current of a transformer depends upon the secondary current which, in turn, depends upon the load supplied by the transformer. There is not enough information in the question to determine the rated primary and secondary currents of the transformer.