0
It you use a counter to control a loop for ten repetitions and express the condition as WHILEcounter 10 which one what is true A counter is a constant and 10 is a constant counter is a con?
Wiki User
∙ 16y ago
Assuming the choices are:
A counter is a constant and 10 is a constant.
or
A counter is a constant.
I'd have to say that that makes no sense, since a constant is something that cannot be changed, and a counter changes every iteration. However, maybe they're teaching something different in school these days. However, I know for sure that 10 is a constant, since it is a defined real number who's value will never change (the number ten will always refer to having exactly ten of something, not eleven or nine.), so -
Since 10 is a constant:
"A counter is a constant and 10 is a constant" must be true.
Maybe repost it, if I'm misunderstanding the question?
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
What is the difference between entry and exit controlled loops - in Java?
while loop and for loop are entry controlled loops as they check looping condition at the entry point. do while loop is exit controlled loop as it checks looping condition at exit point. shreeradha@yahoo.com
Why variable voltage and variable frequency control is used instead of variable voltage?
variable voltage control has some limitations as you decrease the voltage corresponding phase current will increase lead to increase of flux which lead to saturation of motor core and heating of motor to make flux constant and vary speed of motor v/f ratio need to be maintained constant
What are the effects of feedback on time constant of control systems?
1.feedback in control system improves the speed of response2.using feedback in control system we can reduce the sensitivity of the system to parameter variation
Why the partial safety factor of concrete is higher than that for steel?
because concrete is unpredictable than steel
Definition of sentinel-controlled loop?
In a Sentinel-Controlled loop, a special value called a sentinel value is used to change the loop control expression from true to false.For example,when reading data we may indicate the "end of data" by a special value,like -1 and 999.The control variable is called sentinel variable.A sentinel-Controlled loop is often called indefinite repetition loop because the number of repetitions is not known before the loop begins executing.
What is a condition which remains constant or unchanged in an experiment?
A control variable is a condition that remains constant or unchanged in an experiment. Its purpose is to serve as a baseline for comparison to see the effects of manipulating other variables.
What do you called the constant condination?
The constant condition referred to in programming is typically represented by a Boolean expression that evaluates to either true or false. This condition is used to control the flow of a program by determining whether a particular block of code should be executed.
When an individual goes without eating for a day his or her blood surgerlevel remains about the same throughout the day this relatively constant condition is maintained by?
homeostatic control
When an individual goes without eating for a day his or her blood sugar level remains about the same throughout the day. This relatively constant condition is maintained by?
homeostatic control
When an individual goes without eating for a day his or her blood sugar level remains about the same throughout the day This relatively constant condition is maintained by?
homeostatic control
What is along and digital control system?
A: The last time that i kept up with types of systems there were only three what is along?. Well anyhow type-0 system is one that requires a constant error signal to operate type-1 a constant rate of change of the controlled variable requires a constant error signal under steady state condition. type 1 is usually referred as servomechanism system. type-2 a constant acceleration of the control variable requires a constant error under steady state condition. type-2 sometimes is referred to as zero velocity error system
What is the difference between a control variable and a control treatment?
A control variable is a factor that is held constant in an experiment to prevent it from influencing the outcome. A control treatment, on the other hand, is a specific group or condition in an experiment that receives no experimental manipulation and is used as a baseline for comparison with the treatment groups.
Is the control another name for constant?
No.
How are constant and control related?
they are the same
What is an example of something at constant speed but not constant velocity?
You are driving your car with cruise control but you steer around a bend in the highway. The cruise control keeps your speed constant, but by steering you change your direction and thus your velocity is not constant.
Is a variable that stays the same a constant independent variable or control?
Control
What is a ccrm?
Constant Control Relay Module
