0
What else can I help you with?
How does a Shockley diode work?
A Shockley diode uses a metal-semiconductor junction instead of a p-n semiconductor-semiconductor junction. This results in a device with a much lower forward bias voltage drop and much faster switching times.
What is pressure drop across rotameter?
The pressure drop across a rotameter is the difference in pressure between the inlet and outlet of the device, caused by the flow of fluid through its tapered tube. This drop occurs due to the fluid's acceleration as it passes through the narrowing section, resulting in a decrease in pressure as described by Bernoulli's principle. The pressure drop is influenced by factors such as flow rate, fluid viscosity, and the geometry of the rotameter. It is important to consider this drop when designing systems to ensure proper operation and accurate flow measurement.
What are 2 advantages for this particular control voltage?
With voltage control there is so much voltage drop due to resistor, that's the disadvantage
How do you check IGBT with multimeter?
IGBT JUNCTION TEST PROCEDURE 1. Short out G1 to E1 and G2 to E2. With a multimeter set to check diodes, check across the C1- C2E1 junction. With the (+) probe on C1 and the (-) probe on C2E1, you should see an open circuit. Switch the probes. You should see a diode drop on the meter. 2. Check across the C2E1-E2 junction. With the (+) probe on C2E1 and the (-) probe on E2, you should see an open circuit. Switch the probes. You should see a diode drop on the meter. 3. With a 9 volt* battery, connect the (+) terminal to G1 and the (-) terminal to E1. Using your meter (set to check diodes), should see a diode drop across the C1-C2E1 junction in both directions now. Connect the (+) terminal to G2 and the (-) terminal to E2. You should see a diode drop across the C2E1-E2 junction in both directions here as well. 4. If the IGBT passed all of the above tests, the IGBT is good. * You may be able to use a second multimeter as a voltage source by setting it to check resistance at its lowest available resistance scale. The (+) probe is the positive side. However, not all meters provide enough DC voltage for this, and may even give you false readings. A known DC voltage from 8 to 15 volts is recommended instead.
What are splices and taps in wires?
A tap splice is a splice that is made usually in a mid span of aerial feeder conductors. It is used to connect a home from a utility company's secondary service drop on the street where the span is between poles and it is not convenient to connect a mid span home to either pole. Tap splices are also made in underground services where the utility feeders are in conduit between junction boxes. Each home along the route has an underground conduit from the junction box to the homes meter base. In the junction box where the home service wires connect to the utility feeders, this splice is known as a tap splice.
If an evaporator has a pressure drop of10psig and the low side pressure is 15psig what is the pressure at the inlet of the evaporator?
To find the pressure at the inlet of the evaporator, you subtract the pressure drop from the low side pressure. Given a low side pressure of 15 psig and a pressure drop of 10 psig, the inlet pressure would be 15 psig - 10 psig = 5 psig. Therefore, the pressure at the inlet of the evaporator is 5 psig.
What factors affect compressor capacity?
pressure drop in inlet filters and poor maintenance of equipment
What is the junction voltage drop a silicon diode?
It is generally accepted to be approximately .7 volts.
For the same size of pipe when mass flow rate is also same what will happen to the pressure drop if change in inlet pressure takes place?
If you change the inlet pressure, you outlet pressure will also change dramatically.
What makes a car idle to drop when coming to a stop?
the inlet manifold could Be leaking so check the gaskets or the injector seals
What is flash separation?
A flash separator consists of a vessel where the pressure is lower than the inlet stream. When the inlet stream enters the tank (which has a larger volume), the pressure may drop, as well as the temperature. When the pressure drops, the vapors dissolved in the liquid inlet will boil, "flash," into the vapor phase. Thus, the dissolved gases in the liquid are separated by "flashing" them.
Will air pressure drop if a bigger air hose distributed to smaller air hose?
No. At the junction of the small hose to the pressure is great
What is mean flash separator?
A flash separator consists of a vessel where the pressure is lower than the inlet stream. When the inlet stream enters the tank (which has a larger volume), the pressure may drop, as well as the temperature. When the pressure drops, the vapors dissolved in the liquid inlet will boil, "flash," into the vapor phase. Thus, the dissolved gases in the liquid are separated by "flashing" them.
How does a Shockley diode work?
A Shockley diode uses a metal-semiconductor junction instead of a p-n semiconductor-semiconductor junction. This results in a device with a much lower forward bias voltage drop and much faster switching times.
What are the advantages of using drop bar brake levers on a road bike?
Drop bar brake levers on a road bike offer advantages such as improved aerodynamics, multiple hand positions for comfort on long rides, and better control and braking power.
What are the advantages of using drop bars on a gravel bike?
Drop bars on a gravel bike offer multiple advantages. They provide different hand positions for comfort on long rides, improve aerodynamics for faster speeds, and offer better control and stability on rough terrain.
Are Junction boxes used wire exposed portions of the basement?
They can be used if need be. But, know that all junction boxes must be covered and they must be accessible at all times. That can be placed above a drop ceiling with panels that can be removed but not above a permanent sheet rock or wood ceiling.
