0
Add your answer:
Earn +20 pts
What is 12 add 2?
14
What is 2 plus 12-7 times 4 divided by 2?
2+12-7*4/2 = 2+12-28/2 = 2+12-14 = 14-14 = 0
What multiplies in to 24 and adds to-14?
The numbers are -2 and -12 because -2 times -12 = 24 and -2+(-12) = -14
What does 14- 2 tell an electrician?
12
What is th gcf of 12 and 14?
the gcf of 12 and 14 is 2
Can you turn a 14-2 wire into a 14-3?
The only way to change a 14-2 wire into a 14-3 wire is to physically remove the 14-2 and replace it with a 14-3.
What is the difference between 12 -2 and 14 -2 wire?
Both 12-2 and 14-2 wire have 2 wires in a single cord. Neither contains a ground wire. Size 12 wire is a larger wire than size 14 wire. Size 12 wire can carry more amperage without getting hot and burning up. They would not be used for house wiring or machinery since they do not have a ground wire.
Can you connect 12-2 wire to 14-2 wire together?
You cannot connect 12-2 wire and 14-2 wire together. This can be dangerous, and it will cause issues with the circuit.
Can 12-2 wire be used where only 14-2 wire is required?
Yes the ampacity of #12 is 20 amps whereas the ampacity of #14 is 15 amps, so you are well within the range using #12 wire.
What is the difference between 12-2 and 14-2 wiring?
The '12' and '14' refers to the gauge of the wire. A 14 gauge wire is used for circuits drawing 15 amps or less; general lighting and outlets. A 12 gauge wire is used for 20 amp circuits, like dishwashers, disposals, and microwaves. The '-2' refers to the number of conductors in the wire. 14-2 is a 14 gauge wire with 2 conductors in the sheath. A 14-3 with ground would have three conductors plus a ground in the sheath, for a total of four wires, and is most often used for ceiling fan wiring and three way switches.
Can you replace a short length of 14-2 wire with a 14-3 wire and just not use the red conductor?
Yes, you can replace a short length of 14-2 wire with 14-3 wire and not use the red conductor. Just cap off the red wire with a wire nut at both ends to ensure it is not accidentally connected to anything. Keep in mind that the unused red wire must still be properly terminated in electrical junction boxes.
How do you tell what gauge wire you have in your house?
To determine the gauge of wire in your house, look for markings on the insulation or jacket of the wire. It usually indicates the gauge size, such as 14, 12, or 10. You can also use a wire gauge measuring tool to accurately determine the wire gauge.
Can I in theory have a 12-2 20 amp circuit powering something in a room but tie into that 12-2 with 14-2 to say run small things under the 80 percent rule off it?
If you tie a 14-2 cable into a 12-2 cable that is protected by a 20 amp breaker the 14-2 cable is not protected because its rating is only 15 amps. To comply to the code the added wire will have to be 12-2. Then the whole circuit will be protected by the 20 amp breaker whose wire size 12-2 is rated at 20 amps.
What is the difference between 12 2 and 14 2 wire?
14 gauge wire is smaller and is only good for 15amps of load. 12 gauge wire is a little bigger and is good for 20 amps of load, that is best case. there are many other factors that apply such as length of wire run, how long the power is applied, how many conductors are parrellel to each other etc.
What is 12 add 2?
14
Is it safe to go from 12-3 wire to a 14-2 wire in the middle of a switch leg?
No. The wire size is dependent on the circuit protection. If the circuit uses a 20 amp breaker you need to run 12 AWG wire on all devices connected to that circuit.
Can you use 14-2 wire for 230 volts?
No, 14-2 wire is typically rated for 120 volts. For 230 volts, you would need to use a heavier gauge wire such as 10-2 or 12-2 to handle the higher voltage and current. It's important to always use the correct wire size for the voltage and current requirements to ensure safety and proper operation.
