0
Add your answer:
Earn +20 pts
How do you put 7 small circles in 3 big ones so that each big circle as 4 small circles?
Draw three circles that touch in a shape of a circle. Draw two small circles in each big one and another in the intersection. It is supposed to be a Venn Diagram.
A tool used to draw a circle?
A compass is a geometric tool used to draw circles.
How do you draw concentric circles?
Leave the point of your compass in the same spot on your paper. Draw one circle, then change the angle to be either larger and smaller, then draw another circle.
How many great circles could you draw that are parallel to the great circle shown in this figure?
zero
How do you create three different drawings showing a number of circles and triangles in which the ratio of circles to triangles is 2 3?
For each drawing . . .-- Draw a small number of circles.-- Draw that same number of circles again.-- Draw that same number of triangles three times.To create a different drawing, do exactly the same thing,but start out with a different small number.
Draw 15 small circles Draw a large circle around three fifth of them?
9
How to draw great circles and small circles drawn?
To draw a great circle on a sphere, start by defining the diameter as the largest circle that can be drawn on the sphere's surface. For small circles, choose a point on the sphere and draw a circle with that point as the center and the radius less than the sphere's radius. Remember that the center of a small circle lies outside the circle on a sphere's surface.
How do you put 7 small circles in 3 big ones so that each big circle as 4 small circles?
Draw three circles that touch in a shape of a circle. Draw two small circles in each big one and another in the intersection. It is supposed to be a Venn Diagram.
How do you draw a poppy step by step?
step 1- draw a circle at the top. step 2- draw a circle at the bottom. step 3-draw two circles at the left and right of the top and bottom circles. step 4-draw a black circle in the middle of all those circles. small tip- you're better to do those 4 circles in red or orange.
How do you draw a panda?
Draw a big circle for the body.Draw a smaller circle on top of that circle to be the head. Draw three little circles inside the top circle to be the eyes and nose. Draw two little circles on top of the top circle for the ears. Draw four cylinders off the large circle for the legs.
How do you create three different drawings showing a number of circles and triangles in which the ratio of circles to triangles is 2 to 3?
To create three different drawings showing a number of circles and triangles in which the ratio is 2:3 you can: Start with an equilateral triangle, draw a circle inside it, draw an equilateral triangle inside the circle, draw a circle in the triangle and then draw an equilateral tiangle in the smallest circle. Or, you could draw 3 triangles and 2 circles in a line. Or, you could draw 3 triangles on a line with 2 circles between them.
A tool used to draw a circle?
A compass is a geometric tool used to draw circles.
How do you draw three and three-fourths?
Draw three whole circles and then draw a circle from which a quarter segment is cut out.
How do you draw non concentric circles?
Draw a circle, then move the point of your compass before you draw another one.
What to draw for polytheism?
A circle with 5 circles within it...that's the symbol for it
How do you draw cute cartoon puppies?
you draw two circles beside each other and then put three dots in them then you make a triangle above the circles then draw a loop for the tongue and then draw half a circle from one circle to the other then draw some eyes and make some ears.
How do you Draw Circles in GstarCAD?
The default method for drawing a circle is to specify a center point and radius.You can draw circles using any of the following methods:Center-RadiusCenter-DiameterTwo pointsThree pointsRadius-Tangent-TangentConvert Arc to CircleTo draw a circle by specifying its center and radiusDo one of the following:Choose Draw> Circle>center, radiusOn the Draw 2D toolbar, click the Circle Center-Radius tool.Type circle and then press Enter.Specify the center point.Specify the radius of the circle.
