0
To calculate the outer diameter of a steel coil, you can use the formula: ( D = \frac{(L \times 1000)}{(\pi \times t)} + t ), where ( D ) is the outer diameter, ( L ) is the length of the steel strip in meters, and ( t ) is the thickness of the steel strip in millimeters. The term ( \pi ) (approximately 3.14159) is used to account for the circumference of the coil. This formula accounts for the thickness of the coil, which adds to the diameter.
What else can I help you with?
How do you calculate rcc hume pipe 1000mm dia np3?
To calculate the RCC (Reinforced Cement Concrete) Hume pipe with a diameter of 1000 mm and NP3 class, you need to determine its dimensions, including the wall thickness and length. The standard wall thickness for NP3 pipes can vary, but it is generally around 50 mm for a 1000 mm diameter pipe. You can then calculate the volume of concrete using the formula for the volume of a cylinder: ( V = \pi \times \left( \frac{D}{2} \right)^2 \times L ) where ( D ) is the outer diameter and ( L ) is the length of the pipe. Finally, multiply the volume by the density of concrete to find the weight of the pipe.
What is the difference in a radius and a diameter?
Radius is from the center of a circle to the outer edge. Diameter is from the outer edge to the opposite outer edge, i.e., through the center. The diameter has twice the length of the radius.
How can you calculate the weight of a ms hollow pipe 200mm ID 8 mm thickness length 1000 mm?
With the information given in the question you cannot. The volume of the pipe is pi(R2 - r2)*L where R = outer radius = outer diameter*0.5 = ID/2 + thickness = 108 mm r = inner radius = inner diameter*0.5 = ID/2 = 100 mm L = length = 1000 mm Next, to convert volume to mass, you need to multiply by the density. You then need to multiply the mass by the gravitational acceleration to convert to weight. If the mass is in kilograms, and the gravitational acceleration is in metres/second2 the result will be in Newtons, the SI unit for weight.
How to calculate area of circle within a circle?
Take out the diameter of the outer circle from the distance between the two. Gives you the diameter of the inner circle then pi r squared it.
What is outer diameter?
hello stupid person! You don't know what outer diameter is...!
How can you calculate the ID of a pipe?
Can you calculate the ID of a pipe when you have the OD to be 10.75" and the wall thickness to be 0.5"Depends on what you know about it. If you have the outer diameter and you know the wall thickness, then ID = OD-2 x wall thickness
What is the thickness of a pipe that has an outer diameter of 2.5 inches and diameter of 2.1 inches?
Consider going across the width of the pipe: Outer diameter = Thickness + Inner diameter + Thickness so 2*Thickness = Outer diameter - Inner diameter = 2.5 - 2.1 = 0.4 inches and therefore, Thickness = 0.2 inches.
How do you calculate the weight of galvanized steel pipe?
To calculate the weight of a galvanized steel pipe, you need to know the length, diameter, and thickness of the pipe. Use the formula: weight = (outer diameter - thickness) x thickness x 0.02466 x length. This formula assumes the density of steel as 7850 kg/m^3 and the length in meters.
Formula to calculate weight of MS pipes per meter length?
The formula to calculate the weight of MS (Mild Steel) pipes per meter length is as follows: Weight per meter = (outer diameter - thickness) * thickness * 0.0246615 * 2.76, where the outer diameter and thickness are in millimeters. This formula takes into account the density of mild steel (7.85 g/cm³) and the conversion factor to get the weight in kilograms per meter. It is important to ensure that the units are consistent throughout the calculation to obtain an accurate result.
How do you calculate weight of bronze pipe?
You calculate its volume, look up the density of bronze, then multiply volume x density to get mass. Probably that's what you want; if you really want weight, you multiply mass x gravity to get the weight.
What is the weight per meter of 200mm dia ms pipe?
The mass of a pipe depends on four variables: ¨ the material it is made from, ¨ its length ¨ its outer diameter ¨ the thickness of the material. The inner diameter can replace the thickness. Without information on all four it is not possible to answer the question. There is no information on the thickness of the material.
What is the difference in a radius and a diameter?
Radius is from the center of a circle to the outer edge. Diameter is from the outer edge to the opposite outer edge, i.e., through the center. The diameter has twice the length of the radius.
How do you calculate the mass of a hollow tube?
To calculate the mass of a hollow tube, you need to know the outer diameter, inner diameter, and length of the tube. First, calculate the volume of the tube by subtracting the volume of the inner hole from the volume of the outer cylinder. Then, multiply the volume by the density of the material to determine the mass.
How do you calaculate the square meter of pipe?
For the inner area, multiply...the inner diameter x pi x the length of the pipe.For the outer area, multiply...the outer diameter x pi x the length of the pipe.
How do you find wall thickness of pipe knowing the outside diameter and inner diameter of pipe?
Outer radius minus inner radius Subtract the inside diameter from the outside diameter, then divide the difference by 2.
How can you calculate the weight of a ms hollow pipe 200mm ID 8 mm thickness length 1000 mm?
With the information given in the question you cannot. The volume of the pipe is pi(R2 - r2)*L where R = outer radius = outer diameter*0.5 = ID/2 + thickness = 108 mm r = inner radius = inner diameter*0.5 = ID/2 = 100 mm L = length = 1000 mm Next, to convert volume to mass, you need to multiply by the density. You then need to multiply the mass by the gravitational acceleration to convert to weight. If the mass is in kilograms, and the gravitational acceleration is in metres/second2 the result will be in Newtons, the SI unit for weight.
How do you calculate the weight of structural steel?
To calculate the weight of structural steel, you can use the formula: weight = volume × density. First, calculate the volume of the steel by multiplying its length, width, and height. Then, multiply the volume by the density of the specific type of structural steel being used to determine the weight.
