0
How do you determine water pressure by how long it takes to fill a two gallon bucket?
Wiki User
∙ 7y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How much water does it take to fill a gallon?
Errrh, would it be a gallon of water?
How many millimetres in a gallon?
none that millimeter is a measurement of length the gallon of the space a liquid takes up
How much water usage does a toilet use?
It takes 1 bucket of water when we flush.
Do two thirty-two ounce make a gallon?
No. Two thirty-two ounce containers equal 64 ounces, which is a half-gallon. It takes 128 ounces to make a gallon.
How much does a gallon of mass weigh?
It depends what is in that gallon bucket. If its full of platinum it'll be a mite heavier then if it was full of pure vacuum. Its a confused question. Weight is how hard earth's gravity sucks on something. In outer space there is no weight. Mass is how much of stuff is in something - its measured by how much force it takes to accelerate it. In outer space mass remains an important factor in doing anything. And gallons are antique imperial units for volume. The weight or mass of a gallon of something can vary widely depending on the density of the material. From helium to uranium the density of stuff varies a lot.
Pipe with a valve at the end The pressure at the valve is 40 PSI you open the valve fully to atmosphere - how do you calculate the flow rate?
Use a 5 gallon bucket and determine the amount of time it takes to fill it. For Example, if it takes 5 minutes to fill up the bucket it is flowing at one gpm. Just take the time it takes to fill the bucket and divide by 5!
How many pounds of force is it to push a 5 gallon bucket under water?
The force required to push a 5-gallon bucket underwater would depend on the buoyancy force exerted by the volume of water displaced by the bucket. This force would be equal to the weight of the water displaced, which can be calculated based on the density of water (about 62.4 pounds per cubic foot). Therefore, you would need a force greater than the buoyancy force to push the bucket underwater.
How many buckets of water does a cow drink everyday?
it takes four gallons to make a gallon of milk not buckets. - Victoria cheyanne seiber
Do you need high water pressure to use a gas powered pressure washer?
No. Typically a gas pressure washer will use less water volume than if you turned your garden hose on full blast. The pressure washer does not depend upon water pressure, but it does need decent volume so be sure to turn your hose faucet to full open once connected.Normal house line pressure of 45-50gpm should work for most residential size pressure washers.A simple test would be to track the time it takes for your garden hose to fill a 2 gallon pail when opened fully vs the same time it would take to fill the bucket with your pressure washer. OK, maybe that second test is not so easy as the pressure will keep knocking the bucket over. Be safe now.
How much does a gallon of liquid butter weigh?
A gallon of liquid butter weighs around 7.5 pounds.
How long would it take to fill a 14 thousand gallon pool?
A day or 2 depending on the water pressure
How many liters it takes to be a gallon?
It takes 3.785 liters.
How many gallons of water does it take to fill an aquarium?
Fill a gallon bucket, timing how long it takes to do so. Then fill your hot tub using the same source... example: if you filled the bucket with a hose, then fill the tub using the same hose. Then time how long it takes to fill the tub and divide the time it takes to fill the tub by the time it takes to fill the bucket and then you know how many gallons it is.
Can you calculate the gallons per minute of a hose if you know the psi of the water flow and the length and diameter of the hose?
You can indeed figure this out using hydraulics formulas. However, a simpler solution. Run the water into a 5 gallon bucket, and time how long it takes to fill the bucket in seconds. Use this formula: Gallons per minute = 300 / TimeToFillBucket
How many five gallon buckets make a bushel of peas?
It takes about 7.5 pounds of peas to make a bushel of peas. This means that it takes about 1 1/2 five gallon buckets of peas to make a whole bushel of peas.
How do you find the flow rate through pipe?
Either by determining the core diametre of the pipe and how long the pipe would be to hold a gallon of water , or simply by running a gallon of water through said pipe and timing it to fill a bucket. Alternately find out the water pressure of the water delivery system and that will help you solve. Is an equation but cannot remember but simplicity is best appraoch...work logically with the information you have re the pipe etc.
How much does 1 cubic foot of water takes to make a gallon?
a gallon or so
