0
Ncvvcm,vncjkvcnv,mcnvjwm,nxvujkcxm,nwjkvm,ncjq,mnjwm,xnjwm,nqwjcvm,cnvkv
vcxnvcx,mnkw,mcnvj,mnjw,mwnjcvm,cxnjmq,nwm,njcm,nj,mcvnjmv,cnvjcm,nwjm,cvn
cvjncxv,mnwm,qm,nea3km,.xmk,qmklvcx,.mkw,.cxmklvcx,.mk.,mcv.cm.,,q.mwk,.mkx,.cxcx
ckvmc,c.mkw,.xmvkcv.,cxvmkv.,mkw,.emkl.c,xmkw,.mkl,.mcxc.xmkxvc
Add your answer:
Earn +20 pts
What is the outside circumference of a pipe if the inside diameter is 1.5 inches and the thickness of the pipe is .25 inch?
The pipe will have an outside diameter of 1.5+.25+.25 = 2". A pipe with an outside diameter of 2" has an outside circumference of 2"*Pi. 2"*3.142 ~= 6.284" or about 6 1/4"
What is the volume of a pipe with diameter of 1 meter and length of 2 meters?
The volume of a pipe with diameter of 1 meter and a length of 2 meters is 1.57 cubic meters.
How many gallons of water does a 10' x 2 pipe hold?
It would have helped if you had provided the size of the pipe. 10' by 2 WHAT? 2 inches? 2 feet, yards, miles?
How do you make a pair of nunchucks?
take a pice of pipe about 3 feet long and cut in into to pices of pipe in to 1 foot 6 inches and cut 2 holes in it and tie 2 nots one on each end in the rope after you put in the holes and now you should have a pair of nunchucks
How much does 2 x 2 square pipe weight?
In what material ?
Can you cut into cast iron soil pipe with plastic soil pipe?
You can put up to a 2 inch pipe into a 4 inch. If you are putting 4 inch to 4 inch, either take out a section of the cast and put the PVC in or cut out a section and connect the PVC to the cast with rubber sleeves meant for this. You can use a saddle clamp for the 2 inch. It is a half round piece of PVC with a 2 inch connection in it. It is held on with two U bolts that go around the cast pipe. Put it where you need it and mark the 2 inch hole on the cast. Drill a series of 1/8 inch holes around this circle. when you get them all drilled, you can break out the plug. Try to keep it from falling into the cast pipe. Put the saddle clamp on and connect the PVC pipe as needed. Seal the saddle clamp to the cast pipe with plumbers putty.
What are the release dates for Black Saddle - 1959 The Saddle 2-2?
Black Saddle - 1959 The Saddle 2-2 was released on: USA: 9 October 1959
How do you tap into an existing 3 PVC drain pipe in order to insert a tee connector?
Measure the length of your tee, subtract 1 1/2 to 2 inches for each socket depth on the ends. The amount that is left over after you subtract for the sockets is what you want to cut out of the existing pipe. You should be able to spread the pipe apart enough to fit the tee in place when ready to glue. Or you can buy a saddle for the size pipe you want to hook in and use a hole saw for that size pipe and drill the hole in the 3 inch on the side. The saddle will fit around the pipe and cover the hole and now you have a non spliced tee. And make sure you use purple primer and heavy duty grey glue when gluing this. It will never leak and does not disolve from harsh toilet bowl cleaners.
How many gallons in a 2 pipe 1 foot long?
The answer will depend on whether it is a 2 inch pipe or a 2 cm pipe or a 2 foot pipe or whatever.The answer will depend on whether it is a 2 inch pipe or a 2 cm pipe or a 2 foot pipe or whatever.The answer will depend on whether it is a 2 inch pipe or a 2 cm pipe or a 2 foot pipe or whatever.The answer will depend on whether it is a 2 inch pipe or a 2 cm pipe or a 2 foot pipe or whatever.
What do you trade for th saddle in poptropica?
1. To get the saddle, find the calf. 2. What to trade for the saddle: the gold pan.
How do you make English crafted tack on horseisle?
For an English saddle pad, you will need 4 cloths, 10 pieces of cotton and 15 of either berries, dandilions, wildflowers, etc. For an English bridle, you will need 5 leather straplings, 2 small buckles and 1 English bit. As for a saddle, it's a litte more complicated. first you need to get a wooden saddle form crafted. This is done by an NPC that I can't seem to remember. You will also need a English saddle base (which is made FROM the saddle form), then craft an English girth, and then to make the saddle you will need 1 English saddle base, 1 English girth and 2 stirrups. *whew!* you can make all these on Rider. -GreatLeonandi, Pinto server
What should you do because your horse are afraid for his sheepskin underneath his saddle?
I can think of only 2 reasons why a horse would react to the underside of a saddle like this. Check and make sure there are not tacks or nails that could be hurting her. Make sure that the saddle has a good fit, otherwise it could make her back sore. If this checks out OK smell the sheepskin and see if it has a funny order. If is smells bad to her she may not want to carry a saddle or rider.
How do we make a kitchen layout plan?
There are many sites that have 2 dimentional and 3 dimensional tools to help plan one's kitchen layout. These sites are Hgtv, Bhg, Merillat and Planyourkitchen.
List four types of common slide layouts?
There are 4 types of layout. 1- Production layout. 2- Process layout. 3- Project layout. 4- Group Layout.
How do you take the saddle off?
These are the steps for taking of the saddle. Always make sure your horse/pony knows where you are when taking off the saddle. Hope they help. 1. Take of the girth by unbuckling the girth straps underneat the saddle flap. 2. Gently lift the saddle of the horse/ponies back. You can take the numnah off aswell. 3. Take off the girth sleeve. Put the saddle away. 4. Check your horse/pony to see if he has girth galls, saddle sores or scratches. 5. Groom your horse/pony.
Is saddle hill a volcano or just a hill?
there are three saddle hills 2 are mountains ones a island
How many syllables in the word saddle?
2
