0
Add your answer:
Earn +20 pts
What is an angle grinder used for?
Angler grinders have many great uses. It can be used to cut metal, wood, rusted bolts, and wire fencing. Angler grinders can either be pneumatic or electric.
How do you remove rusted bolts from a ceramic toilet base?
you have to pull the entire toliet up. Then hopefully the bolts are all that are rusted. the metal (or plastic) flange the toliet carriage head style bolts run into, may be bad also. If this is the case, you will need a plumber, or elevate yourself to a higher degree of knowledge and skill to replace the flange. if just the bolts are bad, you can easily purchase new brass bolts made for toliet hold down, for about $2.00. Some older homes do not have the flange, and the bolts actually have wood screw threads on opposite end. these can be ourcahsed also, and the new bolts just run into the wood floor. However, all older home wood floors with this type of bolts i have wiorked on, the floor is so rotten, ity has to be replaced also. once again, if this is the case, a rotten floor, you need a plumber (carpenter) or have to elevate your knowledge and skill levet to tackle this isssue. if you master the toliet pull alone, make sure to always use a new wax seal gasket, they csot between $1.00 and $5.00. using the old wax gasket will only bring you leaks when you flush.
Step by step instruction removing a 1989 Toyota windshield wiper motor?
Remove wiper arm caps, nuts & arms. Remove cowl louver cover. Disconnect wiper motor electrical connector. Remove 6 bolts and remove wiper linkage assembly. Disconnect wiper link from wiper motor. Remove 4 screws and wiper motor from firewall.
If 1 percent of the bolts made by an automotive factory are defective what is the probability that in a shipment of 175 bolts there are 6 defective bolts?
If 1% of the bolts are defective, then the probability is that close to 2 bolts will be defective if there are 175 bolts. The actual probability is that 1.75 bolts will be defective, but you can not have 3/4 of a bolt. However you know there are going to be runs when you have no errors and runs when you have several error. You would need to make 300 bolts in order to have a run of 125 with no errors to have 3 defective bolts in a run of 1.75 bolts. Likewise, you would need to make a minimum of 600 bolts to have six defective bolts in 1.75 bolts. Then you would have 425 good bolts. However, you are dealing with probabilities, not with getting the machinery started the first thing in the morning. Since there is a 1% error rate, you must assume this is a random rate. It occurs like dice or a coin flip. With the last coin tossed, you have no idea what the next coin flip will be. It is not like the next coin flip will be the opposite. Using the Monte Carlo method, I got .29%. Good luck
How do you change c v joints 1989 topaz?
do not remove strut bolts instead take lower balljoint loose ,take axle nut loose pulling spindle out as you push in on axle, then pry axle out of trans
How do you remove toilet seat with rusted bolts?
Rusting bolts normally indicates that the bolts are brittle. Taking a pair of water pump pliers and squeezing really hard will most of the time break the rusted bolt so you can remove the toilet seat. Otherwise depending on the type of toilet seat installed, you can drill a hole right through exactly where the rusted bolts slot in, so helping you remove the toilet seat.
How do you remove rusted front door in a 1993 dodge caravan the bolts are under the fender. does the fender have to be removed.?
the fender must be well loosened or removed to get to the hinge bolts
How do I remove a rusty old 1993 Ford f 250 front bumper and replace witha new one?
Spray some PB Blaster on the rusted bolts. Remove bolts and take bumper off. Install new bumper and new bolts. Used anti-seize on the bolts.
When penetrating fluid does not remove stuck rusted exhaust bolts what to use?
Oxy aceteline (unsure of spelling) cutting torch most likely.
1990 lesabre sub frame bolts rusted and cracked?
Rusted frame bolts on a 1990 Le Sabre can be hard to remove. Penetration oils, an impact hammer, and even a cutting torch mat be needed. Take care when using a torch that fluids or grease does not catch fire.
Removal of license plate bolts that are rusted in a ford?
The removal of rusted license plate bolts on a Ford starts with the application of penetrating oil. It breaks down the rust and allows the bolts to be removed without breaking.
What is the secret tip to remove the rusted stuck on front brake rotors on your 1997 F-250 4x4 Do you need more muscle a bigger hammer?
You can try spraying the rusted parts with a penetrating oil like wd40 or a product designed to loosen rusted on bolts. Let it soak for a bit before trying to remove. In my experience a big hammer is big help.
Is it difficult to remove exhaust manifold from 1998 jeep wrangler 4.0 engine?
Its a bit of a job because it is held on by the same bolts as the intake manifold, and the easiest way is to remove them both, otherwise the rusted exhaust bolts holding the tubing to the manifold is the worst.
How do you remove rusted bolts from an automobile water pump.?
It is possible to remove rusted bolts from an automobile water pump using a product called Liquid Wrench. Spray the solution on the bolts and let sit for a few minutes. If this does not work, wait 8 hours and then use a torch to heat the bolts.
How do you remove rusted carriage bolts from a wooded seated metal frame picnic bench?
Just use a bolt cutter. You'll have them off in 2 minutes.
How do you remove the upper control arm bolts on a 71 corvette when they are rusted to the frame. The engine is still in the car and the clearance behind the bolt is minimal?
Torches & burn them off
1989 caprice rear shock removeal. Bolts rusted. What size socket for the top bolts?
13 mm
