answersLogoWhite

0

What else can I help you with?

Continue Learning about Math & Arithmetic

How many 1x6's need to cover 480 sq feet?

480/6 = 80


How 1x6 16' to cover 110 sq ft?

To determine how many 1x6 boards, each 16 feet long, are needed to cover 110 square feet, first calculate the area of one board. A 1x6 board is actually 0.75 inches thick by 5.5 inches wide, which converts to 0.0625 feet by 0.4583 feet. The area of one board is approximately 0.0287 square feet. Dividing 110 square feet by this area gives you about 3,833 boards, but since each board is 16 feet long and covers more area, you should calculate using the total coverage of each board properly. You’d actually need around 12 boards to cover that area, considering the actual dimensions.


How many 1x6x16 ft T and ampG boards do I need to cover 801SF?

To determine how many 1x6x16 ft T&G boards you need to cover 801 square feet, first calculate the area covered by one board. A 1x6 board is approximately 0.5 ft wide and 16 ft long, so it covers about 8 square feet (0.5 ft x 16 ft). Dividing 801 square feet by 8 square feet per board gives you approximately 100.125 boards. Therefore, you would need 101 boards to cover the area, accounting for any waste or cuts.


How many deck bd 1x6x16 to cover 740 sq ft?

To determine how many 1x6x16 boards you need to cover 740 square feet, first calculate the coverage of one board. A 1x6 board is 6 inches wide, which is 0.5 feet, and 16 feet long. The area of one board is 0.5 feet x 16 feet = 8 square feet. Therefore, to cover 740 square feet, you would need 740 ÷ 8 = 92.5 boards. Since you can't purchase half a board, you would need to round up to 93 boards.


What does 6 equal to?

12

Related Questions

How many 1x6's need to cover 480 sq feet?

480/6 = 80


How 1x6 16' to cover 110 sq ft?

To determine how many 1x6 boards, each 16 feet long, are needed to cover 110 square feet, first calculate the area of one board. A 1x6 board is actually 0.75 inches thick by 5.5 inches wide, which converts to 0.0625 feet by 0.4583 feet. The area of one board is approximately 0.0287 square feet. Dividing 110 square feet by this area gives you about 3,833 boards, but since each board is 16 feet long and covers more area, you should calculate using the total coverage of each board properly. You’d actually need around 12 boards to cover that area, considering the actual dimensions.


What is the recommended spacing between 1x6 deck boards for optimal installation?

The recommended spacing between 1x6 deck boards for optimal installation is typically around 1/8 to 1/4 inch.


What is the probability of rolling an 18 with three dice?

1x6 x 1x6 x 1x6 =1x36 x 1x6 =1 in 216


Why use spruce 1x6 fascia boards?

If you live in Southern California, you would be better off not using spruce since it has no resistence to drywood termites.


How many 1x6x12 covers 182 square feet?

To determine how many 1x6x12 boards are needed to cover 182 square feet, first calculate the area of one board. A 1x6 board (which is actually 0.75 inches by 5.5 inches) has an area of 0.75 ft x 5.5 ft = 4.125 square feet. Next, divide the total area by the area of one board: 182 sq ft ÷ 4.125 sq ft/board ≈ 44.1. Therefore, you would need approximately 45 boards to cover 182 square feet, rounding up since you can't use a fraction of a board.


How much does 8ft of 1x6 weigh?

How much does 8ft 0f 1x6 weigh


What is the width of the softwood used for laminated boards?

That depends on how wide you need the finished (laminated) board to be. Boards can be laminated in two dimensions: width and thickness. Let's assume you want a laminated board to be 18" wide and 3" thick. You could use, for example, commonly-available boards called 1x4s ("one by fours") and 1x6s ("one by sixes"). Such boards are actually 3-1/2" and 5-1/2" wide, respectively, and 3/4" thick. With these boards, you can build the first layer using alternating 1x4s and 1x6s laid side by side: a 1x4, a 1x6, a 1x4, and a 1x6. That makes the total width 18" (3.5+5.5+3.5+5.5). Or, you could vary the order so that the two narrower boards are both side by side, with two 1x6s on the outside. Repeat this process, changing the order of the narrow and wide boards, so that the "seams" in the second layer do not fall directly on top of those in the first layer. To get your desired 3" thickness, you'll need 4 layers (3/4" x 4 = 3").


1x6?

6


Multiplies of 6?

1x6 2x3


2 plus 1x6?

8


What are all the math factor pairs of 6?

1x6, 2x3