The volume is pi x diameter squared times height//4
The volume collected is 5mm x 100 mm x 100 mm x 3.14/4 = 39250 cu mm = 39.25 cu cm
keep in mind that the rain measurement is still 5mm independent of volume collected.
For wire gauge, 1.25 mm diameter wire is closest to 16 gauge (AWG). See related link.
An internal caliper gauge.
Here's the formula for converting American (or Brown and Sharpe) wire gauge to millimeters:dn = 0.005 mm x 25.4 x 92 36-n/39With this formula, you can convert a wire gauge size to the diameter of the wire in millimeters. The dn is the diameter of the wire in millimeters, as you might have guessed, and the n in the exponent is the gauge of the wire you wish to find the diameter of.Wikipedia has a fine article on this. They have the formula for converting wire gauge to diameter as well as one for calculating cross-sectional area. They also explain where the formula comes from, if you're interested. The formula for converting from diameter to the wire gauge, the inverse of this formula, is also listed, as is a chart. A link is provided for you convenience. Another link is also provided to an online calculator that will let you just put in a diameter or a wire gauge and will do all the work for you. (Note that this calculator works in inches and not millimeters, so you'll have to make a conversion.)Improved Answer By Sandip Vikma :"Above original formula is difficult to calculate. So, you may use bellow derived formula to convert Gauge into MM".dn = 0.127 x 92 [0.9230769-0.025641026n]Where,dn = Thickness in MM.n = Thickness in Gauge.
A 25-gauge needle is smaller in diameter than a 23-gauge needle. The larger the gauge number, the thinner the needle, so a 25-gauge needle has a smaller lumen compared to a 23-gauge needle. This means that for tasks requiring finer needles, such as pediatric or cosmetic procedures, a 25-gauge needle would be preferred.
To convert 22 gauge to inches, you can use the standard wire gauge (SWG) conversion, where 22 gauge is approximately 0.0253 inches in diameter. This measurement can vary slightly depending on the specific type of wire (e.g., steel, copper), but 0.0253 inches is a common standard for 22 gauge wire.
16-gauge wire has a diameter of 0.05082 inches.
Gauge is the term that indicates the diameter of the needle. Most commonly the needles that are used for medical purposed range from 7 Gauge to 33 Gauge, according to the Stubs scale. 7 Gauge needle will have the largest diameter while as the number increase, the diameter decreases. Therefore the 33 Gauge needle has the smallest diameter. So a 26 Gauge needle will have a smaller diameter than that of the 18 Gauge needle.
No its bigger. The smaller the gauge the thicker it is
The funnel increases the area of catchment and makes the reading more accurate by increasing the volume of rain collected. Rainfall statistics must be standardised by specifying the mouth diameter of the funnel if the reading is to have any value.
A wire with a diameter of 4mm corresponds to a wire gauge of approximately 6 AWG (American Wire Gauge). The relationship between wire diameter and gauge is not linear, so different wire diameters can correspond to the same gauge.
gauge
18 G has the larger interior diameter. Gauges are based on AWG ( American Wire Gauge ) So therefore the higher the number the smaller the outside diameter, the lower the number the thicker the outside diameter is.
The gauge is the thickness of the jewelry (Usually the thickness of the wire the jewelry is made from but may also be the diameter of a plug or eyelet). From 20 gauge to 00 gauge, the smaller the number is, the thicker the jewelry is. After 00, the diameter of body jewelry is usually measured in fractional inches A 10 Gauge is smaller than 1/8th of an inch about 2.5 millimeters in diameter!
The larger the wire gauge, the smaller the diameter. 12 gauge is bigger than 14 gauge.
A shotguns gauge is a measure related to the diameter of the smooth shotgun bore and the size of the shotshell designed for that bore. Gauge or diameter of the bore is determined by the diameter of 1 lead pellet times the number of pellets required to equal 1 pound. ex. 12 gauge is equal to the diameter of 1 of the 12 lead balls that equals 1 pound. ex. 20 gauge is equal to the diameter of 1 of 20 lead balls that equals 1 pound. ex. 3 gauge is equal to the diameter of 1 of the 3 lead balls that equals one pound. The larger number of gauge the smaller the bore.
the caliber or gauge
18g