0
To determine which option is better, it depends on the specific application and requirements. The 12.7 scfm at 40 psi provides slightly higher airflow at a lower pressure, which may be suitable for tasks requiring more volume but less force. Conversely, 12.6 scfm at 90 psi offers higher pressure, which can be beneficial for applications needing more force behind the airflow. Ultimately, the choice should align with the specific needs of the task at hand.
What else can I help you with?
How many psi can the pressure rise without reaching the emergency pressure limit if the pressure of the emergency limit is 86 percent and the limit is 93 psi and the pressure is measured in 0.1 psi?
limit is 86% of 93 psi = 86/100 x 93 psi ≈ 79.98 psi As the psi is measured to the nearest 0.1 psi, the safe limit is a measured 79.9 psi.
How many psi is 2.4 bar?
To convert bar to psi (pounds per square inch), you can use the conversion factor that 1 bar is approximately equal to 14.5038 psi. Therefore, to convert 2.4 bar to psi: 2.4 bar × 14.5038 psi/bar ≈ 34.8 psi. So, 2.4 bar is approximately 34.8 psi.
What is 2.4 bar in n psi?
To convert 2.4 bar to psi (pounds per square inch), you can use the conversion factor where 1 bar is approximately equal to 14.5038 psi. Therefore, 2.4 bar is equal to about 34.8 psi (2.4 bar × 14.5038 psi/bar ≈ 34.8 psi).
Conversion of psi to kpa?
Formula: psi x 6.895 = kPa
How much psi does a a water column 23' high have?
10 psi.
What is the oil pressure of the Chrysler 300c at idle?
10 psi minimum, 30 psi would be better.10 psi minimum, 30 psi would be better.
How long will it take to depressurize a 600 gallon air tank from 110 psi to 90 psi?
You can calculate the amount of available air by the following: SCFavailable=Volume of tank(cf)x((P2-P1)/Patm) Volume=600 gal/(7.5 gal/cf) = 80 cu.ft. P2=Compressor High Set Point = 110 psi P1=System Pressure Requirement = 90 psi Patm= Depends on your location, but I'll assume 13.16 psig @ 3000' Available Air = 121.6 cu.ft. Divide by your calculated peak air consumption rate, I will assume 10 scfm. 121.6 cu.ft./10 scfm = ~ 12 minutes You can calculate the time of recovery for your system by dividing by the amount your compressor supply rate. If your air compressor is rated for 30 scfm @ 110 psi and you are continuously consuming 10 scfm while recovering at 30 scfm then take the available air and divide by the difference of your recovery rate and your consumption rate. In this case it would take 6 minutes to fill your tank. Your duty cycle for this example would be run time divided by total time or 6min/18min = 33% duty cycle so I would look for a 50% duty cycle rated compressor. Hope this helps.
At what pressure does propane liquify?
Propane liquifies at a pressure of about 127 psi (pounds per square inch).
How much is 400scfm at 116.0302 PSI in cfm?
To convert from 400 scfm at 116.0302 PSI to cfm, you can use the ideal gas law equation. Assuming standard conditions of 14.7 PSI and 60°F, you can adjust the volume flow rate from the given conditions to standard conditions using the ideal gas law. Applying this equation will give you the equivalent flow rate in cfm at standard conditions.
What should the oil pressure read on a 1991 Jeep Cherokee 4.0L at idle?
On metric gauge 2.5 to 3 bar, about 40 to 45 psi. At least 15 psi, 25 psi would be better, 40 psi on a good engine.
Whatshould be the tire pressure of a 2008 jeep wrangler?
look at the side of the drivers door when it's open you should see a label that tells you the psi. 35 psi is standard I've got mine up at 38. also check it when it comes from the factory psi is usually 29-32 psi. You want the PSI at its highest in the city(better gas mileage) and a lot lower(think 20's) for the trail(better traction)
What is better 5.5scfm at 90 psi or 6.3 cfm at 90 psi?
More cfm's more airflow. Yes, more is better when you are powering certain airtools. Check the air tool specifically to see the demands
How can you make the water pressure better in the toilet?
Flushometer type needs at least 30 PSI to operate semi decently 50 PSI or more would be ideal
What should be the oil pressure on a 2005 jeep wrangler?
Minimum of 15 psi at idle when warm, 30 would be better.Should go over 40 psi at 2000 rpm.Minimum of 15 psi at idle when warm, 30 would be better.Should go over 40 psi at 2000 rpm.
What psi on a dodge avenger?
Engine compression psi? Radiator cap psi? Engine oil pressure psi? Tire pressure psi? Fuel pressure psi?
What is psi in a pressure washer and how does it affect the cleaning performance?
PSI stands for pounds per square inch, which measures the pressure of water coming out of a pressure washer. The higher the PSI, the more forceful the water stream, which can help remove dirt and grime more effectively. Higher PSI generally means better cleaning performance, but it's important to use the right PSI for the surface being cleaned to avoid damage.
How much is one standard atmosphere 7.5 psi 12.5 psi 14.7 psi or 1.5 psi?
One standard atmosphere is equivalent to 14.7 psi.
