answersLogoWhite

0

What else can I help you with?

Continue Learning about Math & Arithmetic

What is the conduction angle for each thyristor in a single phase semi-converter for discontinuous conduction and extinction angle βπ?

In a single-phase semi-converter operating under discontinuous conduction, each thyristor conducts for a conduction angle of α to β, where α is the firing angle and β is the extinction angle. The conduction angle for each thyristor is therefore given by the formula ( \theta = \beta - \alpha ). Since the conduction is discontinuous, this angle is typically less than 180 degrees, resulting in each thyristor conducting for a part of the AC cycle, followed by a period where it is off. In general, the conduction angle can vary based on the firing angle and load conditions, but the key point is that it occurs only for the duration between firing and extinction.


What is meant by switching angle?

The switching angle refers to the specific point in time during an electrical cycle when a switch or device, such as a thyristor or a power electronic converter, is triggered to turn on or off. This angle is crucial in controlling the timing of the switch's operation relative to the alternating current (AC) waveform, influencing the power delivery and efficiency of the system. In applications like phase control for dimming lights or controlling motor speeds, the switching angle determines the effective voltage and power output to the load.


What is firing angle delay?

Firing angle delay refers to the specific time interval in which a control signal is applied to a power electronic device, such as a thyristor or an SCR (Silicon Controlled Rectifier), after the zero crossing of the voltage waveform. This delay is critical in controlling the power delivered to a load by adjusting the phase angle at which the device is triggered. By varying the firing angle, one can regulate the output voltage and current, influencing the performance of AC power control applications, such as in dimmers or motor speed controllers. Essentially, a larger firing angle results in reduced power output.


What is an anticommutator?

An anticommutator is a function of two elements A and B, defined as AB + BA.


What are the types of geometric angles?

Right angle, obtuse angle, acute angle, supplementary angle, complementary angle, interior angle, exterior angle, adjacent angle

Related Questions

What is load commutation?

it is a type of forced commutation technique of thyristor


What is commutation of thyristor?

the process of turning off of a thyrisror is known as commutation


What is a line commutation?

it is the natural commutation ...by making open circuit or short circuit on the thyristor to make it turn off.


What does forced commutation mean?

The term "Forced commutation" is used when a thyristor is turned off using external components. If a thyristor is used in a DC circuit, when first turned on, it will stay on until the current goes to zero. To turn off the thyristor it is possible to use a Forced commutation circuit. The circuit creates a reverse voltage over the thyristor (and a small reverse current) for a short time, but long enough to turn off the thyristor. A simple circuit consist of a precharged capacitor and a switch (e.g. another thyristor) parallel to the thyristor. When the switch is closed, the current is supplied by the capacitor for a short while. This cause a reversed voltage over the thyristor, and the thyristor is turned off.


What is the difference between current and voltage commutation?

Voltage commutation: This is possible in ac circuits...The thyristor gets turned off by reverse bias (negative half cycle) voltage applied across it. This is also called line commutation. Current Commutation: This is possible in dc circuits ...This type of commutation makes use of auxiliary circuit which contains inductor,capacitor,diode and even a thyristor(auxiliary). This is called Forced commutation.


What is line commutation?

i think i know this answer...line commutation is the commutation in single phase inverters/converters when there is current flow back to the source.. It can also refer to a method of turning of a semiconductor device known as a Thyristor or SCR, sometimes called natural commutation. In this method the current between the anode and cathode is interrupted or dropped to a point where the Thyristor can no longer maintain its latch or keep conducting, shutting the device off.


How do you commutate heumann's chopper?

a Heumann chopper is nothing but the Class D commutation of a thyristor.refer to the following link on class d commutationhttp://www.slideshare.net/prathikm/thyristor-commutation-techniques


What is overlap angel of a thyristor?

Overlap angle of a rectifier (μ): The commutation process in a practical rectifier is not instantaneous. During the period of commutation, both the incoming and the outgoing devices conduct current simultaneously. This period, expressed in radians, is called the overlap angle "μ" of a rectifier. It is easily verified that α + μ + γ = π radian.α= Firing angelμ=Overlap angelγ =extiction angel


What is mean of fire angle?

the fire angle is the angle at which the thyristor starts working...


What is class A commutation of thyristor?

it is one of method to turn off scr. resonating LC component is used to turn off scr


What has the author L J Berman written?

L. J. Berman has written: 'A classification of thyristor commutation circuits for static invertors'


What is conduction angle in thyristor?

not a clue a A: It all depends on the thyristor. There are no calculation involved not until you look up the thyristor specifications and decide on the load of the thyristor then you may calculate or more likely choose.