0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Am I wrong if I read meter exponent two as meter squared or meter exponent three as meter cubed?
meter exponent two...
How do you read a meter on a tape measure?
1 meter is about 1 yard and 3 inches or about 39 inches
How do you read an astrolabe?
To read an astrolabe, level the plum bob, the degree scale, the altitude, and the protractor.
How do you read an electrical meter type MS 2 TA 30?
Your electric utility company has a meter department capable of answering this. There are usually pictures of the meter dials/digits included in teaching someone to read the meter, so this is not a good forum to do so. If your electric company does not have the meter in question, find out the manufacturers name, and your utility meter department may help locate a contact at the manufacturer for you. Usually, residential meters have a hot sheet typed up showing how to read them, and the utility will simply mail it to you or possibly scan/fax it.
How to use a bthroom scale?
You just stand on it & read weight.
Why the zero of the ohmmeter scale is usually at the right end of the scale and reading increase towards the left?
Because the meter is actually measuring the current through the resistor, and the two quantities ... current and resistance ... are inversely proportional. So when the meter measures more current, it has to read less resistance, whereas higher resistance will result in less current. So the numbers for resistance have to be printed "backwards" on the meter scale.
There is only 20 volts not 120 volts on outlet that was fine the day before.?
It's possible that there is an issue with the electrical circuit or outlet itself. You may want to check the circuit breaker to see if it has tripped or if there are any loose connections. If you are not comfortable doing this yourself, it's recommended to call a qualified electrician to investigate and resolve the issue to avoid any potential hazards.
How do you read a forcemeter?
To read a force meter, you simply look at the measurement displayed on the dial or digital screen. Make sure to note the units of measurement (usually Newtons) and the scale of the meter to interpret the force applied accurately.
If you reverse the flow on a water meter will it turn the meter backwards?
Yes, a water meter will run backwards. Running your meter backwards is stealing and could result in your service being diconnected and or a fine. Modern meters that are read via radio signals are sofisticated electronic instruments and will report leaks and reverse flows when read. So if your meter is a radio read type you had better not mess with it.
How do you read 277 volts on meter?
To read 277 volts on a meter, simply ensure the meter is set to the appropriate voltage scale (typically AC). Then, connect the meter leads to the circuit or outlet you are measuring. The display should show the voltage reading, which in this case would be 277 volts. Be sure to take appropriate safety precautions when working with electricity.
Can the elecompten read a meter in there office when your meter is broke?
Nope, when the meter's broke there ain't no-one can read it.
How do someone read a medical mechanical scale?
How do you read a medical mechanical scale?
What is the meter reading for a forward biased diode is likely to be when using the diode test range of a digital multimeter?
A: Nobody can answer that. It depends on the diode, battery on the meter, scale of the meter. It should never read zero or close to zero ohms and reversing the lead it should just be close to open but it may read some hi k ohms. A meter test is just to find shorted diodes and extremely leaking diode.
How do I read the electrical testers that I own?
The first step in reading your electrical tester is to determine what type of circuit you are testing and set the meter accordingly. Next you determine the suspected range of the circuit you are testing and set your meter to at least ten times that amount. The red wire is then connected to the positive connection and the black wire is connected to the negative or ground connection. You then read the number from the scale you are working with. For example, the red scale is for AC (houses) and the black scale is for DC currents (car, boat, or RV) Finally, you read the resistance by determining the Ohm reading on the very top scale of black numbers. The amps are determined the same way as voltage.
How do you check alternator 1998 wrangler?
The charging system could be checked at the battery using a volt meter ,place the red lead on the positive terminal the black on the negative ,then set the scale to at least 20 volt scale then start the jeep and read the meter over 12.8 volts is okay 15 volts is to high.
What is the result on the meter reading of clamping the jaws of a clamp-on ammeter around two wires?
If the two wires are on a parallel feed you would read the current through the parallel feeders. If the two wires are "hot " to the load and return back from the load the meter will read zero. The two magnetic fields that surround the wires when a current flows through them will cancel each other. As a result of this there will be no magnetic induction induced into the sensing coil of the clamp on meter.
What is the result on the meter reading of clamping the jaws of a clamp on ammeter around two wires?
If the two wires are on a parallel feed you would read the current through the parallel feeders. If the two wires are "hot " to the load and return back from the load the meter will read zero. The two magnetic fields that surround the wires when a current flows through them will cancel each other. As a result of this there will be no magnetic induction induced into the sensing coil of the clamp on meter.
