0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is 275 subtract 215?
The difference between 275 and 215 is 60.
What is the difference between 90 percent and 60 percent?
33.33% when going from 90% to 60%
What is the difference between 230 million and 60 million?
170 million. (60 + 170 = 230)
What is the difference between 60 degrees N and 60degrees S?
That's a difference of 120 degrees.
What is the difference between a 15 gram ball and a 60 gram ball?
Their difference is that a 15 gram ball is lighter than a 60 gram ball.
Which sandpaper grit size is the most coarse?
The most coarse sandpaper grit size typically starts at around 40 or 60 grit. These lower grit sizes are used for heavy material removal on rough surfaces.
What is the coarse sandpaper?
Coarse sandpaper has lower grit numbers, typically ranging from 40 to 60 grit. It is used for heavy material removal and rough sanding tasks where a smooth finish is not required.
Dffrence between 180 grit sandpaper and 60 grit sandpaper?
The higher the number code printed on the back of all sandpaper the finer the grit. With a little practice you can begin to understand what grit is appropriate for any given job. For instance, I refinish hardwood floors and it requires three courses of sanding. To help quickly remove an old finish from hardwood floors I start with a very course #20 sandpaper. It is so rough that it removes a large amount of material pretty quickly. Then, when I have sanded the floor down to bare wood I "step up" to 60 grit sandpaper. Once I've gone over the entire floor with the 60 grit I "step up" again to the finer 100 grit paper. When refinishing wood floors or furniture it is necessary to use several courses of sanding to help remove the deep scratches created by the rougher grits of sandpaper. I hope this helps. John
How is sandpaper measured?
By the amount and size of grit on the paper. The smaller the number, the less the grit of larger size. the bigger the number, the more the grit of smaller size. 60 grit would be for removing a lot of material, 320 grit would be for finer sanding.
How hard is sandpaper?
Sandpaper comes in different grits, which determine its coarseness. Lower grits (ex. 60) are rougher and more aggressive, while higher grits (ex. 400) are finer and less abrasive. So, the hardness of sandpaper can vary depending on the grit you choose.
What grit of sandpaper should be use to get down to the primer on a car?
220 3m its a finer sand paper you can take the paint as low as you want with it it works great. You should always prime over a 220 grit scratch. It is the perfect size grit. If you are sanding primer so you can apply topcoat, finish with 400grit dry on a machine (DA) or 500 wet sand for a solid color enamel. Basecoat products, particularly metallics and pearls, need to be applied over a substrate that has been wet sanded with 600 grit.
What different grits of sand paper are available?
Sandpaper currently is available in six different grit sizes. Every grit size is used for a different project. The sizes are 40-60, 80-120, 150-180, 220-240,280-320, and 360-600.
What is a 60 grit?
Grit is a word used in specification of grinding wheels. It is used with numbers. Grit means size of the grinding wheel abrasives. So 60 grit means the abrasives filtered in a sieve of size 60(60 slots/inch)
How do you sand and prime furniture made of wood?
If the furniture is painted then you would need approx a 60-80 grit sandpaper, then gradually move to a finer paper. When paint is almost gone finish with about a 320 or 400 grit paper so it is completely smooth. If you want to repaint then you don't need to remove all the paint unless you are painting over an enamel paint with a latex. (oil based vs. water based). You can however prime it with a good primer once the wood is smoothed. Or if you remove all paint you can then stain it. before you paint/stain your wood be sure and remove all dust from the wood with a clean damp cloth. let wood dry and then proceed. good luck and wear a dust mask :-)
Where would you find the terms 80 grit 100 grit and 120 grit?
terms used mostly on sand paper, emery cloth, or other fine abrasive materialYou should always know the type of wood you are finishing before starting any sanding. The type of wood you are sanding has a direct relationship to the grit used for final sanding. There are two basic types of wood - softwoods and hardwoods.Typical softwoods are Pine and Fir. Softwoods can be finish sanded with 150 or 180 grit prior to the application of primer. Please see Grit Guide for more information:Grit GuideVery Fine (220) For light sanding between stain and sealer. Fine (150-180) For final sanding or cleaning of wood surfaces. Medium (100-120) For moderate removal of surface imperfections. Course (60-80) For heavy removal of wood and coatings. * http://www.nortonconsumer.com/Data/Element/Node/Application/Application_edit.asp?ele_ch_id=A0000000000000001555"What are the grit sizes equivalent to?" United Kingdom:-UF Ultra Fine:- approximately equivalent 420 Grit sandpaper.F Fine:- approximately equivalent 320 Grit sandpaper.M Medium:- approximately equivalent 220 Grit sandpaper.C Coarse:- approximately equivalent 180 Grit sandpaper.XC Extra Coarse:- approximately equivalent 120 Grit sandpaper.XXC Extra, Extra Coarse:- approximately equivalent 80 Grit sandpaper USA:-UF Ultra Fine:- approximately equivalent 140 Grit sandpaper.F Fine:- approximately equivalent 120 Grit sandpaper.M Medium:- approximately equivalent 100 Grit sandpaper.C Coarse:- approximately equivalent 60 Grit sandpaper.XC Extra Coarse:- approximately equivalent 46 Grit sandpaper.XXC Extra, Extra Coarse:- approximately equivalent 24 Grit sandpaper * http://www.permagrit.com/faq.php
What is the difference between 5 and 65?
60 65-5=60 Difference means you have to substract.
what is the difference between 60 degrees south and 60 degrees north?
One is north, the other south, of the equator. The difference is 60 - (-60) = 120 degrees.
