answersLogoWhite

0


Want this question answered?

Be notified when an answer is posted

Add your answer:

Earn +20 pts
Q: What is the nsn for canteen cap used with m-50 mask?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Math & Arithmetic

Which m50 mask accessory should be used if storing for more than 30 days?

Faceform


How you can draw an angle of m50 degree with the help of protector?

Draw a line segment with a straight edge.Place protractor on line segment with the center point on the end of the line and the line lined up with the bottom guide.Place a small dot on the 50o mark on the protractor.Place the straight edge on the end of the line segment and on the dot and connect the two.


Cbrne module 3 pre-test?

1. a,b,c2. b - results to UCC3. 1- remove a half sheet of m8 paper... 2-Dip the paper into the liquid 3-Observe the m8 paper for color changes 4-compare any color change 5-report results 6-discard m8 paper4. d - It changes color5. a - red6. b - black7. a - Exhaled air is directed through the outlet valve and front module covor8. b - local logistics readiness flight personnel will measure your face length using a caliper9. b - it will leak causing possible illness or death in a contaminated environment10. b - sitting erect with your head level, your mouth closed, and your teeth lightly together11. b,c,e - upon issue, prior to turn-in, prior to deployment12. d - immerse the mask in the disinfecting solution13. a,c,e - The threads are damaged. It is dented deeper than 1/4 inch. It is dented on a seam.14. a - turn in the mask15. c - 1/4 inch16. b - replace the harness17. d - Separation of the silicone from the metal surface to which it's bonded18. d - turn in the mask19. a - the straight side of the D-ring on the shoulder strap of the carrier20. b - incorrect installation may cause toxic agents to leak into the mask20a. outward21. b - fit the narrow rib into the groove where the lens and the mask are bonded21a. a - replace it with a new second skin22. a - large rib at the bottom, facing outward22a. a - install the second skin around the drinking tube23. c - With the front voicemitter toward the open end of the bag23a. b - force the air out of the bag24. c - make sure long hair is tied back and hangs outside of your GCE jacket25. c - Run a finger under each temple tab, front to back.25a. c - loosen the neck straps26. c - you perform the negative pressure check and the lens remains deflected after holding your breath26a. b - by the front of the facepiece27. a - stop breathing and close your eyes tightly27a. c - 9 seconds28. a - determine proper fit -- if the lens remains deflected, this give an indivation of an initial proper fit29. a - reverse it over the face of the mask29a. d - place the m50 head first and the m45/mcu-2 filter first and upright facing away from the body30. d - hook-and-pile fastner tape at the fly31. a,b,e,f - The manufacture date, part of the national stock number (NSN), the contract number, garment size32. a,b,e - centered in the middle of the back of the hood, horizontally above the eyelens on the front of the hood, over the right breast of the coat32a. d,c,e - first and last name, rank, service component33. d - wash it33a. a - by marking the labels inside the coat and trousers34. a - over the combat boots35. a - outer gloves and glove liners35a. c - to protect your feet and ankles from contamination36. c - to protect your feet and ankles from contamination37. b - Secure all overgarment fasteners on each ankle so that they fit snugly around the protective footwear.38. c - leather gloves38a. a - 2 minutes39. a - 32F