The power of a motor can be calculated using the formula: Power (P) = Work (W) / Time (t). In this case, the work done is 4000 joules and the time is 20 seconds. Therefore, P = 4000 J / 20 s = 200 watts. Thus, the power of the motor is 200 watts.
To calculate the work done by a 1 kW motor in one minute, we can use the formula: [ \text{Work} = \text{Power} \times \text{Time} ] Given that power is 1 kW (or 1000 watts) and time is 1 minute (or 60 seconds), we can substitute the values: [ \text{Work} = 1000 , \text{W} \times 60 , \text{s} = 60000 , \text{J} ] Thus, a 1 kW motor does 60,000 joules of work in one minute.
To find the time it takes for a 500 W electric motor to do (1.50 \times 10^5) J of work, we can use the formula: [ \text{Power} = \frac{\text{Work}}{\text{Time}}. ] Rearranging gives us: [ \text{Time} = \frac{\text{Work}}{\text{Power}} = \frac{1.50 \times 10^5 \text{ J}}{500 \text{ W}} = 300 \text{ seconds}. ] Thus, it would take 300 seconds, or 5 minutes, for the motor to perform that amount of work.
1 minute = 60 seconds. You now have all the information required to work out, for yourself, the answer to this and similar questions.
Power = Work/Time Time = Work/Power Work = Power * Time See related links for a power calculator. Insert work and time to calculate power.
Gold Medal winners in rowing or triathlon would probably be the best to power a small motor..
Did you check for power to the motor? If the switch doesn't work then the motor won't work. If there is power to the connector that hooks onto the motor then the part may be defective, if not then trace it back.
The resistor has power going to it but, the resistor may be burned out and no power is coming out of it. Check for power at the blower motor connection.
"Power" is the rate of doing work (delivering energy).A motor that is operating at higher power is delivering more energy per second, so it does greater work for the same interval of time than the second motor.Here's a note though: The rating marked on a motor is the power it's capable of delivering, but not necessarily the power it is delivering whenever it's running. If your two motors had the same loads on them, then they'd be operating at the samepower level and doing the same amount of work per second, even though one might be capable of handling a greater load.
Check to see if you are getting power and ground to motor - if so and motor does not work- bad motor
I think it can work with a certain type of generator and an electric motor like one that uses 300w/h The idea is to run a generator that can produce more electricity than needed to run the motor that is powering it.
To determine which wires to join on a 1980 or 81 4500 citation motor after cutting out the harness, it is best to locate a manual or see a qualified mechanic. Electrical work like this is always best left to a professional.
why does blower motor not work on 1984 Monte Carlo.It is new and it is getting power?
Mutli speed furnace motors work on a basis of horse power verses work load. The motor actually contains multiple windings or you could say multiple motors. Each of the windings has a specific horse power rating at a given work load. For example, a 3 speed 1/2 horse power motor is actually 3 different horse powers. High is 1/2 hp - medium is 1/3 hp - low is 1/4 hp. As the motor horse power is decreased the motor will slow down under a given or constant work load. Technically there is no such thing as a multi speed motor but in actuality a multi horse power motor.
They use the DC power from the batteries to run an electric motor to power the vehicle.
It will not work at all.
A bad power window motor is the most common reason for a power window not to work. A blown fuse is the second most common reason for a power window not to work.