Wiki User
โ 14y agoThere are several kinds of dipole; the most common is the half-wave dipole.
Its total length is fairly close to half the wavelength of the design frequency.
The length needs to be adjusted slightly to compensate for the thickness of the elements and for end-effects.
If the length is wrong by ten or twenty percent it will alter the feed impedance, but have little effect on the gain.
Wiki User
โ 14y agoWavelength = (speed) / (frequency) =(299,792,458) / (1,240,000) = 241.768 meters
Of course. The wavelength and amplitude have no influence on each other.
Wavelength = speed/frequency = 30/10 = 3 meters
Frequency = (speed) / (wavelength) = 900/9 = 100 Hz.
0.0003 nanometres.
The wavelength is calculated using the formula: Wavelength = Velocity / Frequency. Substituting the values given, we get Wavelength = 15 / 5.4 = 2.78 meters. Hence, the length of the wave is 2.78 meters.
Wavelength is a physical quantity that represents the distance between successive peaks (or troughs) of a wave. It is measured in units of length, such as meters or nanometers, depending on the type of wave.
The length of the rope would be half the wavelength of the standing wave, so in this case, the rope would be 5 meters long. This is because the fundamental frequency of the standing wave has one full wavelength, which corresponds to half the length of the rope.
Radio waves have the longest wavelength in the electromagnetic spectrum, ranging from several meters to kilometers in length.
The speed of the wave would depend on the tension, the length of the rope, and the mass per length unit.On the other hand, there is a general relation for waves: speed = wavelength x frequency. This doesn't help in this particular case - you need more data.By the way, Hz. is a unit of frequency. Wavelength would be measured in meters.The speed of the wave would depend on the tension, the length of the rope, and the mass per length unit.On the other hand, there is a general relation for waves: speed = wavelength x frequency. This doesn't help in this particular case - you need more data.By the way, Hz. is a unit of frequency. Wavelength would be measured in meters.The speed of the wave would depend on the tension, the length of the rope, and the mass per length unit.On the other hand, there is a general relation for waves: speed = wavelength x frequency. This doesn't help in this particular case - you need more data.By the way, Hz. is a unit of frequency. Wavelength would be measured in meters.The speed of the wave would depend on the tension, the length of the rope, and the mass per length unit.On the other hand, there is a general relation for waves: speed = wavelength x frequency. This doesn't help in this particular case - you need more data.By the way, Hz. is a unit of frequency. Wavelength would be measured in meters.
To make an 11 meter dipole antenna, you will need a length of wire that is approximately 5.5 meters long, as each side of the dipole should be half the wavelength. Attach this wire to a balanced feed line, such as 50-ohm coaxial cable, at the center using a balun or insulator. Hang the antenna horizontally with the ends supported at equal heights for best performance.
Wavelength at 2 MHz = 149.896 meters Wavelength at 56 Hz = 5,353.437 meters Lower frequency --> longer wavelength. Higher frequency --> shorter wavelength When you multiply (frequency) times (wavelength), the result is always the same number.
The metric units for wavelength are meters (m) and for frequency are Hertz (Hz).
Meters are a unit of measurement of length and have no relation to weight. One metric tonne is 1000 Kilograms.
To calculate the frequency, you can use the formula: frequency = speed of sound / wavelength. The speed of sound in air is approximately 343 meters per second. Since the wavelength is equal to the length of the room (5 meters), the frequency would be 343 / 5 = 68.6 Hz.
"Meters" is not frequency. It's wavelength. If you know the wavelength in meters, divide 300 by it, and the result is the frequency in MHz. If you know the frequency in MHz, divide 300 by it, and the result is the wavelength in meters.
The wavelength of a wave is measured in meters (m) or any other unit of length, such as nanometers (nm) or micrometers (ยตm).