0
6 piles, up to 2.4 metres in diameter, extend up to 50 metres into rock
- 61,000 cubic metres of concrete was used to build Q1
- 9,300 tonnes of steel reinforcing
- 250 tonnes of structural steel in the roof and spire
- 18,926 panes of glass
- 1000 kms of electrical cabling in the lifts of Q1 was used in the building enough to stretch from the Gold Coast to Sydney!
- Sand from the site was taken by the truckload to replenish Surfers Paradise beach
- Q1 sits on 1.2 hectares of land
- The project cost approximately $255 million AUD
- The spire is made of steel and glass, is 97.7 metres in height and begins at level 75
- Illuminated by arc lights, the spire is visible 200kms away
- During the construction phase a new level went up every four day
What else can I help you with?
What percent of data falls above Q1?
In a standard distribution, the first quartile (Q1) represents the 25th percentile of the data. This means that 25% of the data falls below Q1, and consequently, 75% of the data falls above Q1. Therefore, 75% of the data is above Q1.
Write the Arden's method to convert an NFA to DFA with expression?
here first we looking on the given diagram and after this we select all the incoming input like in q1 all the input are q1=q2 0+ q1 1 or q2=q3 1 + q2 0 q1 is a state and when q2 sent 0 then its going to q1 so the value add into the q1 ok same in q2...
How do you find q1 of a data set?
To find Q1 (the first quartile) of a data set, first, arrange the data in ascending order. Then, identify the position of Q1 using the formula ( Q1 = \frac{(n + 1)}{4} ), where ( n ) is the number of data points. If the position is a whole number, Q1 is the value at that position; if it's not, Q1 is the average of the values at the closest whole numbers surrounding that position.
If q1q2q3 are three quartiles then Coefficent of quartile deviation is?
coefficient of quartile deviation is = (q3-q1)/(q3+q1)
What percent of your data lies between q1 and q3?
In a dataset, the interquartile range (IQR), which is the range between the first quartile (Q1) and the third quartile (Q3), contains 50% of the data. This means that 25% of the data lies below Q1, 50% lies between Q1 and Q3, and another 25% lies above Q3. Therefore, the percentage of data that lies between Q1 and Q3 is 50%.
Where is the Q1?
Q1 is a building found at Gold Coast in Australia.
What percent of data falls above Q1?
In a standard distribution, the first quartile (Q1) represents the 25th percentile of the data. This means that 25% of the data falls below Q1, and consequently, 75% of the data falls above Q1. Therefore, 75% of the data is above Q1.
What was the state of apple in q1 in 1996?
what was the state of the apple opmany in q1 1996
What was the state of the company in Q1 1996?
what was the state of the apple opmany in q1 1996
How big is the Q1 Australia?
Australia's tallest building is the Q1 Tower on Queensland's Gold Coast. The Q1 Tower has 80 floors and is 322 m high.
How tall is Q1?
Q1 Tower on Queensland's Gold Coast is Australia's tallest building (as of 2014). The Q1 Tower has 80 floors and is 322 m high.
What was the state of the apple company in Q1 1996?
what was the state of the apple opmany in q1 1996
Write the Arden's method to convert an NFA to DFA with expression?
here first we looking on the given diagram and after this we select all the incoming input like in q1 all the input are q1=q2 0+ q1 1 or q2=q3 1 + q2 0 q1 is a state and when q2 sent 0 then its going to q1 so the value add into the q1 ok same in q2...
How do you find q1 of a data set?
To find Q1 (the first quartile) of a data set, first, arrange the data in ascending order. Then, identify the position of Q1 using the formula ( Q1 = \frac{(n + 1)}{4} ), where ( n ) is the number of data points. If the position is a whole number, Q1 is the value at that position; if it's not, Q1 is the average of the values at the closest whole numbers surrounding that position.
What is the formula for coefficient of quartile deviation?
coefficient of quartile deviation: (Q3-Q1)/(Q3+Q1)
What is the formula of unitary elastic demand?
ed=(q1-q2)/q1/(p1-p2)/p1
How is micromax q1?
Type your answer here... Micromax Q1 is a mobile, which costs about Rupees 1400-1800
