answersLogoWhite

0

When Rack angle is zero... Chip thickness ration is going to be greater.

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Math & Arithmetic

Why thickness of chip is more than the depth of cut?

The thickness of the chip is more than the depth of cut because the machining process involves the removal of material in a way that the chip must accommodate the tool's geometry and cutting action. When the cutting tool engages the workpiece, it not only displaces material but also creates a chip that is thicker at the cutting edge due to the force exerted and the deformation of the material. Additionally, the cutting process often involves shear forces that contribute to the chip's thickness exceeding the nominal depth of cut. This results in a chip that is typically thicker than the depth measured directly at the cutting edge.


Where would you find a point with a ratio greater than 1?

Any point where x/y is greater than 1 has a ratio larger than one. For example, the point (2, 1) has a ratio of 2:1, or 2. (3, 1) has a ratio of 3, etc.


What ratio diameter to thickness of cylinder determines thin or thick cylinder?

If the ratio of thicness to dia of cylinder is 0.1 and less, it is thin. And if this ratio is more than 0.1 it is thick cylinder


Is 10mm thicker than 12mm?

No, 10mm is not thicker than 12mm. In fact, 12mm is thicker than 10mm by 2mm. Millimeters measure thickness, so a higher number indicates a greater thickness.


How do you calculate compression ratio?

compression ratio = compressed size / uncompressed size the ratio should be between 1 and 0 (multiply with 100 to get the ratio in percent) a ratio greater than 1 means, the compressed size is actually greater than the uncompressed size a ratio just below 1 means bad compression the lower the ratio, the better the compression

Related Questions

What is the chip thickness ratio?

In a machining process, a sharp tool cuts through some workpiece, generally by skimming along its surface. The "depth of cut" is the measurement of how far beneath the surface of the workpiece the tool is penetrating. The "chip thickness" is the thickness of the material being cut away. One might think that the thickness of the removed material would be equal to the depth of cut, and sometimes it is. In that case, the chip thickness ratio is 1.0. However, depending on many other factors (cutting tool geometry, material properties, etc.), sometimes the chip will be thicker or thinner than the depth of cut, due to deformation of the chip as it is removed. This change of thickness as the chip material is being removed is defined as the "chip thickness ratio."


Is 1.094 and .094 the same thickness?

No because 1.094 is greater than .094


Where would you find a point with a ratio greater than 1?

Any point where x/y is greater than 1 has a ratio larger than one. For example, the point (2, 1) has a ratio of 2:1, or 2. (3, 1) has a ratio of 3, etc.


What is thin cylinder?

for thin cylinder the thickness to diameter ratio should be less than 0.07


Can poisson's ratio be greater than 1?

yes * * * * * No, it cannot be greater than 0.5 See link for more details.


Is the tangent ratio number is greater than one?

The tangent ratio can take any real value.


What ratio diameter to thickness of cylinder determines thin or thick cylinder?

If the ratio of thicness to dia of cylinder is 0.1 and less, it is thin. And if this ratio is more than 0.1 it is thick cylinder


Is 10mm thicker than 12mm?

No, 10mm is not thicker than 12mm. In fact, 12mm is thicker than 10mm by 2mm. Millimeters measure thickness, so a higher number indicates a greater thickness.


How do you calculate compression ratio?

compression ratio = compressed size / uncompressed size the ratio should be between 1 and 0 (multiply with 100 to get the ratio in percent) a ratio greater than 1 means, the compressed size is actually greater than the uncompressed size a ratio just below 1 means bad compression the lower the ratio, the better the compression


What is 'portrait orientation'?

A vertical to horizontal ratio greater than 1.


What is thicker 6mm or 2mm?

6mm is thicker than 2mm. It has a greater thickness of 4mm.


What does it mean when the ratio is greater than 1?

When a ratio is greater than 1, it indicates that the quantity in the numerator is larger than the quantity in the denominator. This suggests a favorable or positive condition, depending on the context. For instance, in financial metrics, a ratio greater than 1 might indicate profitability or more assets than liabilities. In other contexts, it can signify a majority or dominance of one element over another.