answersLogoWhite

0

Here is some info that might help. In short though, a reduction of that size is not advisable as it could cause excess pressure and reduce the performance of the pump. http://www.zoeller.com/zcopump/TechBriefs/HomesHiddenAlly.htm Good Luck. Tom

User Avatar

Wiki User

20y ago

What else can I help you with?

Continue Learning about Math & Arithmetic

How many 0.50 inches diameter pipes are equal to the 1.50 inches diameter pipe?

Nine.


Which will carry most water 2 small pipes with a radius of 2 and 3 inches or the larger single pipe with a radius of 5 inches?

To start, we will find the cross sectional area of the pipes. Pipe with radius of 2 inches Cross sectional area = PI x radius2 = 12.56 inches2 Pipe with radius of 3 inches Cross sectional area = PI x radius2 = 28.26 inches2 Pipe with radius of 5 inches Cross sectional area = PI x radius2 = 78.5 inches2 As the cross sectional area of the pipe with a radius of 5 inches (78.5 inches2) is greater than the sum of the cross sectional areas of the pipes with radii of 2 inches and 3 inches (40.82 inches2), it can be concluded that the pipe with a radius of 5 inches will be able to carry the most water. (Assuming that all three pipes are the same length).


Can washer drain pipe be one inch draining into one and a half inch?

Yes, if the joint between the 2 width of pipes is made to be tightly closed so that no leakage would occur. The best would be to use a connector with a 1 inch diameter at one end and a diameter of 1.5 inches at the other end. Or maybe, if the 2 pipes are vertical, to put the 1 inch pipe into the 1.5 inches pipe and seal the 2 pipes with a good amount of resistant tape so that the water will go straight from one pipe to the other with no leakage. But with hot water draining from the washer, even with the cold water, the tape solution is probably just a temporary solution, because the tape would break down after some time.


Are pipes measured by the diameter or circumference?

Diameter.


Did Romans use aquaducts for protection?

No, aqueducts were used to carry water. They were big water pipes which carried water to wherever it was needed.No, aqueducts were used to carry water. They were big water pipes which carried water to wherever it was needed.No, aqueducts were used to carry water. They were big water pipes which carried water to wherever it was needed.No, aqueducts were used to carry water. They were big water pipes which carried water to wherever it was needed.No, aqueducts were used to carry water. They were big water pipes which carried water to wherever it was needed.No, aqueducts were used to carry water. They were big water pipes which carried water to wherever it was needed.No, aqueducts were used to carry water. They were big water pipes which carried water to wherever it was needed.No, aqueducts were used to carry water. They were big water pipes which carried water to wherever it was needed.No, aqueducts were used to carry water. They were big water pipes which carried water to wherever it was needed.

Related Questions

How do you fix foghorn sound in water pipes?

By installing a Shock absorber


What are the necessary steps for installing bathroom rough-in plumbing?

The necessary steps for installing bathroom rough-in plumbing include planning the layout, marking the locations for fixtures, cutting and installing pipes, securing the pipes in place, and testing for leaks before closing up the walls.


How to unthaw frozen pipes effectively and safely?

To effectively and safely unthaw frozen pipes, you can use a hairdryer, heat lamp, or heating pad to gently warm the pipes. Avoid using open flames or high heat sources, as they can damage the pipes. Additionally, keep faucets open to allow water to flow and relieve pressure as the pipes thaw.


How can I prevent pipes from banging in my home?

To prevent pipes from banging in your home, you can try installing water hammer arrestors, securing loose pipes, adjusting water pressure, and insulating pipes to reduce vibrations.


How can I prevent pipes from knocking in my home?

To prevent pipes from knocking in your home, you can try installing water hammer arrestors, securing loose pipes, adjusting water pressure, and insulating pipes to reduce vibrations.


How can I prevent water pipes from banging?

To prevent water pipes from banging, you can try installing water hammer arrestors, securing loose pipes, adjusting water pressure, and insulating pipes to reduce vibrations.


How can I stop noisy pipes when flushing the toilet?

To stop noisy pipes when flushing the toilet, you can try adjusting the water pressure, insulating the pipes, or installing a water hammer arrestor.


How can I safely and effectively unfreeze water pipes in my home?

To safely and effectively unfreeze water pipes in your home, you can use a hair dryer, heat lamp, or heating pad to gently warm the pipes. Avoid using open flames or high heat sources. You can also wrap the pipes with towels soaked in hot water or use a portable space heater to warm the area. It's important to slowly thaw the pipes to prevent damage. If you're unsure or unable to safely unfreeze the pipes yourself, it's best to contact a professional plumber for assistance.


How can I prevent or stop banging pipes in my home?

To prevent or stop banging pipes in your home, you can try installing water hammer arrestors, securing loose pipes, adjusting water pressure, or insulating pipes to reduce noise and vibrations.


How to thaw pipes effectively and safely?

To thaw pipes effectively and safely, you can use a hairdryer, heat lamp, or heating pad to gently warm the frozen area. Avoid using open flames or high heat sources. You can also wrap the pipes in towels soaked in hot water or use a portable heater near the pipes. Be patient and avoid using excessive force to prevent damage to the pipes.


How to unthaw water pipes effectively and safely?

To safely and effectively thaw frozen water pipes, you can use a hair dryer, heat lamp, or heating pad to gently warm the pipes. Avoid using open flames or high heat sources, as they can damage the pipes or cause a fire hazard. Additionally, keep the faucet open to allow water to flow and relieve pressure as the pipes thaw.


How can I repair or replace shower pipes in the wall?

Repairing or replacing shower pipes in the wall involves cutting out the damaged section of pipe, removing it, and installing a new pipe in its place. This process may require cutting into the wall to access the pipes, so it's important to turn off the water supply before starting. It's recommended to consult a professional plumber for this task to ensure it is done correctly and safely.