Want this question answered?
When dealing with conrete the "slump" refers to how much will a sample sag, reduce in height in a given time frame. re: a 5" slump means that after removing the CYLINDER the concrete will lose 5 inches of elevation. The slump cylinder is the tool used to determine the slump of concrete.
No. Slump is "faster" but still at a very slow rate
Use a spectrometer to measure the wavelength of the light. There is a direct, but inverse correlation of the wavelength to the temperature.
dry concrete
It depends on the density of the substance being measured. There is no direct conversion. Milligrams are a measure of mass, cubic centimetres are a measure of volume.
Slump test is the most commonly used method of measuring workability of concrete.It does not measure all factors contributing to workability, nor is it always representative of the placability of the concrete.However, it is used conveniently as a control test and gives an indication of the uniformity of concrete from batch to batch.
The slump test was first introduced in 1918 by an engineer named Frederick C. Davis at the University of Illinois. It was initially used in construction to measure the workability of fresh concrete.
the workability of a concrete mixture
The importance of slump test in concrete work is to ensure consistency in the concrete. The test measures the workability of the concrete.
The importance of slump test in concrete work is to ensure consistency in the concrete. The test measures the workability of the concrete.
Slump test is the most commonly used method of measuring workability of concretewhich can be employed either in laboratory or at site of work.It is seen that the slump test gives fairly good consistent results for a plastic-mix. This test is not sensitive for a stiff-mix. In case of dry-mix, no variation can be detected between mixes of different workability. In the case of rich mixes, the value is often satisfactory, their slump being sensitive to variations in workability.
The slump test gives fairly good consistent results for a plastic-mix. This test is not sensitive for a stiff-mix. In case of dry-mix, no variation can be detected between mixesof different workability. In the case of rich mixes, the value is often satisfactory, their slump being sensitive to variations in workability.
Pavement quality concrete, (PQC) measurement of workability by determination of compacting factor will be more appropriate than slump.It is not a suitable method for very wet or very dry concrete.It does not measure all factors contributing to workability, nor is it always representative of the placability of the concrete.
A low slump in concrete refers to a situation where the concrete mixture is relatively dry and stiff. This results in poor workability and more difficulty in placing and consolidating the concrete.
The slump test is suitable for site use because it is a simple and quick way to measure the workability of concrete, making it convenient for on-site applications. It requires minimal equipment and can be easily performed by construction workers without specialized training. The results of the slump test provide valuable information about the consistency of the concrete, helping workers make real-time adjustments to achieve the desired quality of the concrete mix.
An unacceptable amount of slump in concrete is generally considered to be when the measured slump falls below the specified range set by the project specifications or design requirements. This could indicate issues with the concrete mix design, workability, or handling procedures, which may lead to compromised strength and durability of the concrete. It is important to address and correct any slump deficiencies to ensure the quality of the finished concrete.
Slump check does not measure strength. It measures workability. Workability is the ease with which concrete can be placed in position. Correct as far as it goes! Slump refers to workability however it is also, all telling as to the water content of the mix. The more water, the easier it will work! Problem becomes, too much water will increase the porosity making the concrete weak and susceptible to early degradation because contaminates are able to enter and commence corrosion of embedded steel. A concrete that is easy to work that has a high water content [ more than .40 ] is known for shrinkage cracking due to rapid evaporation of the high water content. These cracks caused by rapid loss of water decrease compressive strength and invite early corrosion. This type of concrete also experiences, curling and ASR as well as efflorescence in a very short time period. Strength is a function of correct hydration, slow internal curing and careful design of a mix for the intended service criteria and not a whole lot to do with slump!