answersLogoWhite

0

It is perfectly acceptable to have (2) 120 volt 15 amp receptacles operated from a 120 volt 20 amp circuit breaker (as a general rule of thumb 11 receptacles are acceptable on a 20 amp circuit). The 15 amp rating of the receptacle is the maximum allowed amperage that should be hooked up to the receptacle at any one time. So in this case the limiting factor is the amount of current being drawn across both receptacles simultaneously should not exceed the 20 amp rating of the circuit breaker.

In the United States the NEC code allows the use of a 20 amp circuit breaker to feed a branch circuit consisting of 15 amp receptacles. Generally you would not exceed 11 receptacles though as you will assume an average load of 1.5 amps per receptacle and trying to maintain about 80% max load.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Natural Sciences

Duplex receptacle circuit given 15 amp breaker 225 amp load?

A 15 amp breaker is not sufficient for a 225 amp load. You would need a breaker that matches the load current, such as a 225 amp breaker. Using a 15 amp breaker for a 225 amp load would cause the breaker to trip immediately due to overcurrent.


Can you use both 15 amp and 20 outlets on the same circuit?

No. You need 20 amp receptacles. ( if a single receptacle on an individual brach circuit NEC 210.21 (B)(1) ) Yes you can use a 15 amp receptacles on a 20 amp breaker in the states but not in canada. ( branch circuit supplying two or more receptacle NEC 210.21(B)(3) ) 15 amp receptacle on a 20 amp circuit is not code, partly because 20 amp circuits use #10 ga wire, which does not fit unto a 15 amp receptacle,(can be forced but lots of work.) Also a 15 amp receptacle will not take the 18 amps continuios that a 20 amp recep. will. ( It is code, see above. 14 awg = 15 amp, 12 awg = 20 amp, 10 awg = 30 amp ) 20 amp wire is 12 gauge not 10 Yes you can use 15A outlets and swithes on 20 amp breakers they are UL listed for 20 amp even if they are stamped for 15A as long as the wire is 12ga to. ( NEC Table 210.21 (B)(3) )


Can you use two 15 amp single pole breakers in place of a double pole 30 amp breaker?

Yes. An everyday occurrence of this circuitry is in your kitchen counter split receptacles. The top half of the receptacle is a 15 amp circuit and from the same breaker the bottom half of the receptacle is another 15 amp circuit. A two pole single handle breaker is a common trip. If one of the circuits fed from the breaker faults the other connected circuit will shut off also. If you are talking about slot position in a breaker panel, you can remove the two pole breaker and install two single pole breakers.


Can you wire 15 amp plug on a 20 amp circuit?

No. Also it would be a moot point using a 20 amp receptacle because the breaker protecting the circuit will only be a 15 amp. If you use a 20 amp breaker then make sure that the wire size is #12 and that you remove the 15 amp receptacle from the circuit as it will be not rated for the new 20 amp current.


Can you replace a 20 amp circuit breaker with a 25 amp circuit breaker?

No. The breaker must protect the circuit components such as wiring, outlets and switches that are connected to the breaker. Therefore if you have a 30 amp circuit as dictated by its components you need to protect it with a 30 amp or less breaker.

Related Questions

Duplex receptacle circuit given 15 amp breaker 225 amp load?

A 15 amp breaker is not sufficient for a 225 amp load. You would need a breaker that matches the load current, such as a 225 amp breaker. Using a 15 amp breaker for a 225 amp load would cause the breaker to trip immediately due to overcurrent.


What is the proper electrical requirement for a 30 amp dryer receptacle?

The proper electrical requirement for a 30 amp dryer receptacle is a dedicated 240 volt circuit with a 30 amp circuit breaker and a 3-prong or 4-prong outlet.


Can you change a 50 amp receptacle to a 15 amp receptacle?

Yes as long as you change the 50 amp breaker to a 15 amp breaker. You will be hard pressed to get the 50 amp #6 wire under the terminals of the 15 amp receptacle.


Can I safely install a 20 amp receptacle on a 15 amp circuit?

No, it is not safe to install a 20 amp receptacle on a 15 amp circuit. The receptacle should match the circuit's amp rating to prevent overloading and potential fire hazards.


What happens when you put a 20 amp receptacle on a 15 amp circuit?

When you put a 20 amp receptacle on a 15 amp circuit, it can lead to overloading the circuit and potentially causing a fire hazard. The receptacle may not provide the necessary protection for the circuit, leading to safety risks. It is important to match the receptacle's amp rating with the circuit's amp rating to ensure safe electrical operation.


What are the necessary requirements for installing a 50 amp welder receptacle in a workshop?

To install a 50 amp welder receptacle in a workshop, you will need a dedicated 50 amp circuit breaker, appropriate gauge wiring (typically 6-gauge for a 50 amp circuit), a NEMA 6-50R receptacle, and proper grounding. It is important to follow local electrical codes and regulations when installing the receptacle to ensure safety and compliance.


Can a 240 volt receptacle go on a 15 amp circut breaker?

In North America you would need two 15 amp breakers to obtain 240 volts. The wire for a 15 amp circuit would be #14 AWG. So to answer the question, yes a 240 volt receptacle can go on a 15 amp circuit.


How do you add a 240 volt receptacle to 100 amp supply?

The 240 volt receptacle has to have an amperage rating. It is this rating that governs the wire size and breaker size to feed the circuit. The new two pole breaker will be inserted in the 100 amp distribution if space is available and connected to the new wiring that terminates at the new receptacle.


What are the necessary specifications for installing a 50 amp outdoor receptacle?

To install a 50 amp outdoor receptacle, you will need a dedicated circuit with a 50 amp breaker, appropriate wiring rated for 50 amps, a weatherproof outlet box, and a receptacle designed for 50 amp usage. It is important to follow all local electrical codes and regulations when installing the receptacle.


Can you use both 15 amp and 20 outlets on the same circuit?

No. You need 20 amp receptacles. ( if a single receptacle on an individual brach circuit NEC 210.21 (B)(1) ) Yes you can use a 15 amp receptacles on a 20 amp breaker in the states but not in canada. ( branch circuit supplying two or more receptacle NEC 210.21(B)(3) ) 15 amp receptacle on a 20 amp circuit is not code, partly because 20 amp circuits use #10 ga wire, which does not fit unto a 15 amp receptacle,(can be forced but lots of work.) Also a 15 amp receptacle will not take the 18 amps continuios that a 20 amp recep. will. ( It is code, see above. 14 awg = 15 amp, 12 awg = 20 amp, 10 awg = 30 amp ) 20 amp wire is 12 gauge not 10 Yes you can use 15A outlets and swithes on 20 amp breakers they are UL listed for 20 amp even if they are stamped for 15A as long as the wire is 12ga to. ( NEC Table 210.21 (B)(3) )


Can you use two 15 amp single pole breakers in place of a double pole 30 amp breaker?

Yes. An everyday occurrence of this circuitry is in your kitchen counter split receptacles. The top half of the receptacle is a 15 amp circuit and from the same breaker the bottom half of the receptacle is another 15 amp circuit. A two pole single handle breaker is a common trip. If one of the circuits fed from the breaker faults the other connected circuit will shut off also. If you are talking about slot position in a breaker panel, you can remove the two pole breaker and install two single pole breakers.


Can a 15 amp receptacle be safely used on a 20 amp circuit?

No, a 15 amp receptacle should not be used on a 20 amp circuit as it may not be able to handle the higher current and could pose a safety risk.