Wiki User
β 14y agoI actually have a 400w hps ballast and I can also use my 400w metal halide bulb in it with no problem.
So what your saying is they do, but they dont? the answer is, they dont. You can get universal bulbs hps to plug into a mh ballast they have a miniturized igniter inside the bulb.
As I understand it, a 400W metal halide bulb can be used with a 400W hps ballast, but not the converse. A MH bulb has the igniter in the bulb, and the HPS has it in the ballast--which pretty much goes along with your comment above. Apparently the double presence of the igniter in the HPS setup is OK.you can run metal halide in same wattage's but not hps in metal halide systems.you can run such as (same wattage's)250 watt metal halide-400 watt halide ect in hps systems but not hps bulbs in halide systems. they make conversion bulbs to run halide in hps as well and vice versa.
Wiki User
β 13y agoNo, a high pressure sodium bulb requires a specific ballast designed for high pressure sodium bulbs. The ballasts for metal halide bulbs are not compatible with high pressure sodium bulbs, as they operate at different voltages and currents. Attempting to use the wrong type of bulb with a ballast can result in damage to the bulb or the ballast.
Wiki User
β 15y agoInteresting question. I've dealt with all types of HID (high intensity discharge) lighting fixtures, including low pressure sodium lamp fixtures, which are uncommon. Although I can't say for sure, I doubt the voltage level supplied by the low pressure sodium fixtures ballast, or transformer and capacitor, will be correct for "firing" the metal halide lamp, the voltage will likely be too low. Try it and see if it works, but I doubt it. No, the output voltage is too low for the lamp to start.
Wiki User
β 14y agoNo. HID ballasts are designed for use only with the type of lamp it's made for. It must match the type and wattage exactly. There are a few exeptions to this rule, though.
Exception 1 - Metal halide ballasts will run a Mercury vapor lamp.
Exception 2 - There are metal halide lamps made for use with HPS ballasts for retro fitting lamps to the cleaner look of metal halide, without costly ballast and/or fixture replacements.
Those are the only 2 I know of off hand.
Wiki User
β 14y agoNo, metal halide lamps require the electrical operating characteristics that the associated metal halide ballast produces. A high-pressure sodium ballast also is equipped with an igniter, used to "strike the arc" in the mating HPS lamp. Such a starting igniter is not required for firing a metal halide lamp, therefore, an HPS ballast will not produce the correct electrical circuit to start and maintain a metal halide lamp.
Wiki User
β 12y agoNo. You must stick with proper lamp style and wattage for that fixture
Wiki User
β 12y agoNo they both use different style ballast.
Wiki User
β 14y agoNo.
Wiki User
β 11y agoYes
No. The bulb has to match the ballast wattage exactly. And you can't interchange different lamps (like metal halide) either. The ballast is specific to that wattage and lamp type. The bulb will either burn out quickly or just not work properly at all
No, metal halide and mercury vapor lamps do not use the same ballast. Metal halide lamps require a ballast specifically designed for metal halide lamps, while mercury vapor lamps require a ballast designed for mercury vapor lamps. Using the wrong ballast can result in poor performance and potential safety hazards.
To ignite a 400W electronic metal halide or high pressure sodium bulb, you need to ensure that the power supply is connected and turned on. These bulbs require a ballast to regulate the electrical current, so make sure the ballast is functioning properly. Once everything is set up, simply turn on the power switch, and the bulb should ignite.
No, it is not recommended to use a 70 watt metal halide lamp with a 150 watt ballast. The lamp and ballast wattage should match to ensure proper operation and to prevent damage to the lamp or ballast. It is best to use a compatible lamp and ballast with matching wattages.
Yes, you can replace a mercury vapor bulb with a metal halide bulb as they are both types of HID (high-intensity discharge) lighting. However, you may need to also replace the ballast to match the new bulb type, as metal halide bulbs usually require a different ballast. Additionally, check the wattage and size of the new metal halide bulb to ensure it is compatible with the fixture.
No, the ballast has to be matched to the lamp. 250 watt ballast, 250 watt lamp. Also be sure to match the lamp type to the proper ballast even though the wattage is the same. HPS ballast to HPS lamp, Metal halide ballast to metal halide lamp and mercury vapour lamp to mercury vapour ballast.
You can generally determine if a halophane light is metal halide or high pressure sodium by looking at the color of the light it emits. Metal halide lights produce a white or bluish-white light, while high pressure sodium lights emit a yellowish-orange light. Additionally, you can refer to the manufacturer's specifications or labels on the light fixture for more information.
No. The bulb has to match the ballast wattage exactly. And you can't interchange different lamps (like metal halide) either. The ballast is specific to that wattage and lamp type. The bulb will either burn out quickly or just not work properly at all
No. The lamp has to match the ballast. The lamp will not ignite if the wrong ballast is used.
No, metal halide and mercury vapor lamps do not use the same ballast. Metal halide lamps require a ballast specifically designed for metal halide lamps, while mercury vapor lamps require a ballast designed for mercury vapor lamps. Using the wrong ballast can result in poor performance and potential safety hazards.
To ignite a 400W electronic metal halide or high pressure sodium bulb, you need to ensure that the power supply is connected and turned on. These bulbs require a ballast to regulate the electrical current, so make sure the ballast is functioning properly. Once everything is set up, simply turn on the power switch, and the bulb should ignite.
A metal halide ballast works just by transforming the line voltage into much more useful voltage to the metal halide, and by regulating the current so that the bulb will have its useful life at the most.
No, it is not recommended to use a 70 watt metal halide lamp with a 150 watt ballast. The lamp and ballast wattage should match to ensure proper operation and to prevent damage to the lamp or ballast. It is best to use a compatible lamp and ballast with matching wattages.
Yes the ballast and starter are the same you can run halide in hps, but not hps in halide.
Make sure you are using a metal halide bulb and the ballast is matched to the wattage on the bulb. These both must be correct.
The 4 types are: flourescent incandescent metal halide high pressure sodium
yes No Rafe, it will not. Remember when you tried it.