0
No, a 6 amp switch should not be used to control a 12 amp motor as it may cause the switch to overheat and fail due to exceeding its amperage rating. It is important to match the switch's amperage rating with the motor's amperage to ensure safe and proper operation.
Add your answer:
Earn +20 pts
Why would you need a 20 Amp Single Pole Switch insted of a 15 Amp?
A 20 Amp single pole switch is needed when the circuit requires higher amperage capacity to safely control the load. Using a 15 Amp switch on a circuit that requires 20 Amps could lead to overheating and potential fire hazards. Always match the switch's amperage rating with the circuit's requirements for safety and proper functionality.
Can I use a 30 amp circuit with a 12 gauge wire to handle a tablesaw that runs at 13 amps under load but spikes above 30 amps on turning on as the 20 amp circuit kept tripping at turn on?
It is not safe to use a 30 amp circuit with a 12 gauge wire for a tablesaw that spikes above 30 amps on startup. This setup can pose a fire hazard and may not provide adequate protection. Consider upgrading to a properly sized circuit and breaker to ensure safe operation of your tablesaw.
What would cause a 12 volt motor to change polairity?
A reversal of polarity in a 12-volt motor can occur if the wiring connections are switched or if a DPDT (double pole, double throw) switch is used to change the direction of current flow through the motor. It can also happen if a control circuit such as an H-bridge is used to control the motor direction.
Is a 15 amp power tool better than a 12 amp?
Not necessarily. The amp rating of a power tool indicates its motor's power consumption, not necessarily its performance. Other factors like quality of construction, design, and intended use will determine the overall performance of the tool. Choosing between a 15 amp and a 12 amp tool should be based on the specific requirements of the task at hand rather than just the amp rating.
What is stronger 9 amp or 12 amps?
A 12 amp current is stronger than a 9 amp current because amperage is a measure of electrical current flow. More amps indicate a higher flow of electricity, which means a 12 amp current can power larger devices or provide more energy than a 9 amp current.
Why would you need a 20 Amp Single Pole Switch insted of a 15 Amp?
A 20 Amp single pole switch is needed when the circuit requires higher amperage capacity to safely control the load. Using a 15 Amp switch on a circuit that requires 20 Amps could lead to overheating and potential fire hazards. Always match the switch's amperage rating with the circuit's requirements for safety and proper functionality.
Does a 4 hp motor have better starting torque than a 12 amp motor?
YES
How loud will a 12 amp motor be in a vacuum cleaner?
A 12-amp motor is fairly standard and will be about as loud as a typical vacuum cleaner, that is to say loud enough to scare gunshy dogs and babies but not loud enough to be overbearing.
Is as strong 12 amp drill or 19.2 amp drill?
The more amps any tool pulls, the stronger it's motor is.
What is the wattage rating of a Somfy 12 volt motor model no ct32-rt-12?
Motor: 12v AMP usage: 1.2amp Watt: 12x1.2=14.4W
What is the power consumption on this vaccuum?
The Boss SmartVac 4870GZ uses a 12-amp motor.
Can I use a 30 amp circuit with a 12 gauge wire to handle a tablesaw that runs at 13 amps under load but spikes above 30 amps on turning on as the 20 amp circuit kept tripping at turn on?
It is not safe to use a 30 amp circuit with a 12 gauge wire for a tablesaw that spikes above 30 amps on startup. This setup can pose a fire hazard and may not provide adequate protection. Consider upgrading to a properly sized circuit and breaker to ensure safe operation of your tablesaw.
Can you use a 10 amp switch to open a window in a 12 volt dc system?
No, you cannot use a 10 amp switch to open a window in a 12 volt DC system. This is because the switch would not be able to handle the current necessary to power the window motor. The amount of current required to open a window in a 12 volt DC system is typically much higher than 10 amps, and so the switch would not be able to cope with the load. In addition, the switch would not be able to sustain the current necessary to keep the window open, which could lead to the window becoming stuck in the open position. Furthermore, the switch would not be able to handle the circuit protection requirements necessary to keep the window safe. For these reasons, it is not recommended to use a 10 amp switch to open a window in a 12 volt DC system.
Can a 240 Volt switch rated at 10 amps handle 30 amps at 12 Volts?
no a 240V switch rated at 30amps may work ok but could be a problem with a motor or coil if the switch is not dc rated chances are the 240V switch opens far enough to break a 30 amp arc, even if its not fast enough
Which vacuum has the greatest suction power?
Hoover steam vacs have a 12 AMP motor which is very good.
What would cause a 12 volt motor to change polairity?
A reversal of polarity in a 12-volt motor can occur if the wiring connections are switched or if a DPDT (double pole, double throw) switch is used to change the direction of current flow through the motor. It can also happen if a control circuit such as an H-bridge is used to control the motor direction.
Will a 12 dc volt 8 amp power supply run a 12DC volt 9 amp motor?
Yes but only up to a load torque of 8/9 of the rated torque.
