0
It is not recommended to place an electrical sub panel over stairs as it can create safety hazards. If possible, try to find an alternative location that is easily accessible and not obstructing any pathways. If it must be above stairs, make sure it is properly mounted and securely fastened to prevent any accidents.
Add your answer:
Earn +20 pts
Why would the volts increase from the main panel to the sub panel?
The increase in voltage from the main panel to the sub panel may be due to the resistance in the wires within the electrical system. As the current flows through the wires, there may be a voltage drop across the length of the wires, which can result in a slight increase in voltage at the sub panel. This phenomenon is known as voltage drop.
How do you wire a circuit panel?
This type of question usually means you aren't ready to do this yourself. Study some electrical material and the National Electrical Code and work this answer out for yourself. If I were to give you an answer, you might attempt to do something you shouldn't be doing, and that may cost someone a shock, a home fire, or their life.
Can you feed a 60 amp sub panel from another 60 amp sub panel?
Yes, you can feed a 60 amp sub panel from another 60 amp sub panel as long as the total connected load does not exceed 60 amps. Make sure to properly size the wire and protect the circuits with appropriate breakers to ensure safe operation of the sub panel.
Is the elctrical panel where electricity enters the home?
No, the electrical panel in a home is where electricity is distributed throughout the home. Electricity enters the home through the main service panel or the electrical meter located outside the home.
What size conductors to run 100 amp sub panel 300 foot away?
For a 100 amp sub panel located 300 feet away, you should use 3 AWG copper conductors. This will help minimize voltage drop over the distance, ensuring the sub panel receives the required amperage reliably. Be sure to consult local electrical codes and regulations for specific requirements in your area.
Why would the volts increase from the main panel to the sub panel?
The increase in voltage from the main panel to the sub panel may be due to the resistance in the wires within the electrical system. As the current flows through the wires, there may be a voltage drop across the length of the wires, which can result in a slight increase in voltage at the sub panel. This phenomenon is known as voltage drop.
What is SDB and SMDB in electrical?
SDB stands for Sub-Distribution Board, which is a panel that receives power from the main distribution board and distributes it to various electrical circuits. SMDB stands for Sub-Main Distribution Board, which is a larger panel that receives power directly from the main distribution board and distributes it to multiple sub-distribution boards.
How do you wire a circuit panel?
This type of question usually means you aren't ready to do this yourself. Study some electrical material and the National Electrical Code and work this answer out for yourself. If I were to give you an answer, you might attempt to do something you shouldn't be doing, and that may cost someone a shock, a home fire, or their life.
Can you have a sub panel in a clothes closet?
No, nor under a stairwell. The electrical code stipulates that there has to be 3 feet or 1 metre in front of an electrical panel for clearance for easy access. The panel being in the closet does not fit this criteria.
When would you want to upgrade the main electrical panel vs just adding a sub-panel?
Depending on how many breakers you have in your exisiting panel if you only have a old 6 or 8 circuit panel then I would suggest a new panel, In the newer building world where you have a 20 or 30 circuit panel then I would suggest a sub panel.
What is an electrical bonding strap?
How do i install aluminum bonding strap in sub panel of 100 amp service
How do you connect 200amp from main panel to sub panel to the lug of the min panel to lug of sub panel?
Not exactly sure what your question is and you need to make sure you are in compliance with electrical code for your jurisdiction. But, generally speaking you install a large breaker (let's say 100A 2 pole breaker to power the sub panel) just as you would install any other breaker in the presently used (hot) panel, and the proper sized cable then goes from old to new and terminates on the main lugs of the new panel. Ground and neutral are usually isolated from each other in the sub panel but depends on other factors as to location of the sub panel, etc.
What is a sub panel?
A sub-panel is always fed from a main panel. The main panel is situated where the electrical service wiring first enters the main structure on a dwelling plot or building site.A sub-panel can be situated within the same building as the main panel or it can be in a subsidiary building or structure (such as a garage, garden shed or workshop) that is separate from the main building.More informationA sub-panel is another name for a secondary breaker box, just as "the main panel" is another name for "the main breaker-box"."Breaker-box" and/or "panel" are just alternative short names that are used instead of the full name "circuit breaker box".
How do you change out small sub panel to a bigger sub panel?
Home owner big jobIn the trade this is called a sub panel change out. It is a complicated job in as much as you have to know wire sizes, ampacity of wires and proper electrical workmanship. Such a project should be left to a licensed electrical contractor to take out the proper permits and call for proper inspections. By taking this route it will leave you confident that if any mishaps happen to the installation down the road your insurance company will be behind you 100%.
Does a sub panel need a main breaker?
Answer for Canada, USA and countries running a 60 Hz, 120/240 volt, split supply service.The main distribution panelboard has to have a main disconnect. This has been in the electrical regulations since the late 50's.If the sub panel is in the same home under the same roof line, the sub panel enclosure does not need a main disconnect because it is just another branch circuit. Connecting a sub panel to a separate free standing garage or workshop is a different scenario and is governed by a different set of electrical code regulations.What needs to be done to the panelboard is physically remove the neutral bonding screw. This is the screw that bonds the panelboard enclosure to the neutral bus. By doing this it stops a secondary ground pathway for a fault current from the sub panelboard to flow back to the main panelboard on the sub panel's neutral feeder.The electrical code requires that there is only one position on an electrical distribution service where the distribution enclosure and the neutral bus join each other. That is at the main disconnect of the first over current device, which is the main service disconnect breaker or a fused disconnect switch whichever your system uses..
Can you feed from main service panel to sub panel through to relocate meter and use existing panel as sub panel?
Yes it can but it is a complicated job in as much as you have to know wire sizes, ampacity of wires and proper electrical workmanship. Such a project should be left to a licensed electrical contractor to take out the proper permits and call for proper inspections. By taking this route it will leave you confident that if any mishaps happen to the installation down the road your insurance company will be behind you 100%.
Can you feed a 60 amp sub panel from another 60 amp sub panel?
Yes, you can feed a 60 amp sub panel from another 60 amp sub panel as long as the total connected load does not exceed 60 amps. Make sure to properly size the wire and protect the circuits with appropriate breakers to ensure safe operation of the sub panel.
