Yes
You can if you have a neutral wire present. If the existing switch is what is called a "switch loop" then you can not change the existing switch to a switched outlet. You can identify a switch loop by looking at the wires coming into the switch bow. If there are only one set of wires usually a black and white and they go directly to the switch then you have a switch loop
Most switched outlets have one half that's hot all the time. If that's the case it will be as easy as changeing the outlet. In the center of each side of the outlet there is a small piece of copper connecting the two screws. Look and see if the copper piece is broken on the hot side, if it is then replace the outlet using the constant hot. Cap off the unused wire from the switch. If both sides of the outlet are switched then you can remove the two wires from the switch and tie them together. then either replace the switch and have a dummy or put on a blank cover. You should be all set.
Disconnect the circuit breaker or fuse to that outlet. Then disable or replace the outlet. This is fairly easy and you can buy a new outlet at a home improvement store for a couple of bucks. If you are not comfortable working with these sorts of things call an electrician.
Possibly if you know building code requirements and the circuit requirements. Any electrical work done improperly can be deadly, it will void insurance coverage and could possibly land one in prison if damages occur. Call your local building inspector first, do it right or not at all.
Actually curent or voltage that passes through the object . then there will be a loss .if (current or voltage) the electrical energy is converted into light source , mechanical energy( rotation of fan),chemical reaction(electroplating) as heat (iron box ). so when no object(load) is connected to the plug point there wont be any loss if you r switch on the switch too.
A diagram for a switched outlet shows how an electrical outlet is connected to a switch, allowing the outlet to be turned on and off using the switch.
To wire a switched outlet, you need to connect the hot wire to the brass terminal on the outlet and the neutral wire to the silver terminal. Then, connect the hot wire to the switch and the switch to the outlet. This allows you to control the outlet with the switch. Make sure to turn off the power before starting and follow all safety precautions.
To properly install and wire a switched outlet in your home, follow these steps: Turn off the power to the outlet at the circuit breaker. Remove the existing outlet from the wall. Install a new electrical box for the switch next to the outlet. Run a new wire from the outlet to the switch box. Connect the black wire from the outlet to one terminal on the switch. Connect the white wire from the outlet to the neutral wire in the switch box. Connect the black wire from the power source to the other terminal on the switch. Connect the ground wires together and to the switch and outlet. Install the switch and outlet back into the wall. Turn the power back on and test the switched outlet to ensure it is working properly.
There is no switch on an outlet. You can mount an outlet with the ground up or down. Most electricians I know mount the ground down as I do.
To properly wire a switched outlet in a residential electrical system, you need to connect the hot wire to the brass-colored terminal on the outlet, the neutral wire to the silver-colored terminal, and the ground wire to the green terminal. Then, connect the hot wire to the switch and the switch to the outlet. This setup allows you to control the outlet with the switch. Make sure to turn off the power before working on any electrical wiring.
Yes you just have to "steal" power from the switch. Do this by running a pigtail wire from the hot of the switch to the hot wire of the plug. Make sure you do this before the switch or you will end up with your outlet being switched as well.
To convert a regular outlet into a half switched outlet, you will need to rewire the outlet so that one half is controlled by a switch while the other half remains always on. This involves identifying the hot and neutral wires, disconnecting the tab connecting the two outlets, and connecting the switched wire to one outlet and the always-on wire to the other. It is recommended to consult a licensed electrician for this task to ensure safety and compliance with electrical codes.
You can make music come on with a light switch the same way you can make a light bulb come on - plug a radio into the switched outlet.
an off-load device a a switch where there is no current passing through it when its switched, a isolator is a off load device, a light switch is a on-load device because there is current passing through it when its switched.
You can if you have a neutral wire present. If the existing switch is what is called a "switch loop" then you can not change the existing switch to a switched outlet. You can identify a switch loop by looking at the wires coming into the switch bow. If there are only one set of wires usually a black and white and they go directly to the switch then you have a switch loop
Most switched outlets have one half that's hot all the time. If that's the case it will be as easy as changeing the outlet. In the center of each side of the outlet there is a small piece of copper connecting the two screws. Look and see if the copper piece is broken on the hot side, if it is then replace the outlet using the constant hot. Cap off the unused wire from the switch. If both sides of the outlet are switched then you can remove the two wires from the switch and tie them together. then either replace the switch and have a dummy or put on a blank cover. You should be all set.
The past tense of switch is switched.