Yes you can, However the wire leading out from the breaker must be rated for 30 or more amps, otherwise there is a fire hazard.
Answer for USA, Canada and countries running a 60 Hertz supply service.Yes, a 240v 50amp circuit can be changed to a 120v 30amp circuit. The wire for the 50 amp circuit should be a #6. This is more than ample for a 30 amp circuit. Remove the two pole 60 amp breaker and replace it with a single pole 30 and a single pole 15 amp breaker. One of the two #6 wires will be terminated on the neutral bus (if there is a white use it) and the other #6 will be terminated on the new 30 amp breaker. This will give you the required 120 volt 30 amp circuit. The new 15 amp breaker that was installed just to fill the hole from the two pole 60 amp breaker will give you a spare 15 amp circuit. I have no idea what you are trying to do, but there is no way you can change 220v 50 amp to 120v 30 amp. You can take 220 volt input in the top of your circuit breaker box. Then half of one side will be 120v and half of the other side will be 120v. You can install a 30 amp fuse. You should hire an electrician.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energizedIF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
You can, but your circuit will be "protected" by a 30 amp breaker. So you'll have to consider the safety issues of having wiring and appliances that can draw up to 30 amps before tripping the breaker. Will the wiring and circuity support that much current without damage? If not, then switch to a 15 or 20 amp breaker.
30 amp
No. The breaker must protect the circuit components such as wiring, outlets and switches that are connected to the breaker. Therefore if you have a 30 amp circuit as dictated by its components you need to protect it with a 30 amp or less breaker.
Remove the 30 amp double pole breaker and install at least one single pole 15 amp breaker. It is best if the other slot is not left open so if you have another single pole breaker of any size install it in the 2nd spot so it isn't open when you replace the cover on the panel. For your 15 amp circuit you need #14 gauge copper wire or larger with a hot, neutral, and ground. Your 30 amp circuit was probably wired with #10 gauge conductors. These will probably work on your 15 amp circuit but it may be difficult to connect #10 conductors to devices.
Answer for USA, Canada and countries running a 60 Hertz supply service.Yes, a 240v 50amp circuit can be changed to a 120v 30amp circuit. The wire for the 50 amp circuit should be a #6. This is more than ample for a 30 amp circuit. Remove the two pole 60 amp breaker and replace it with a single pole 30 and a single pole 15 amp breaker. One of the two #6 wires will be terminated on the neutral bus (if there is a white use it) and the other #6 will be terminated on the new 30 amp breaker. This will give you the required 120 volt 30 amp circuit. The new 15 amp breaker that was installed just to fill the hole from the two pole 60 amp breaker will give you a spare 15 amp circuit. I have no idea what you are trying to do, but there is no way you can change 220v 50 amp to 120v 30 amp. You can take 220 volt input in the top of your circuit breaker box. Then half of one side will be 120v and half of the other side will be 120v. You can install a 30 amp fuse. You should hire an electrician.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energizedIF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
You can, but your circuit will be "protected" by a 30 amp breaker. So you'll have to consider the safety issues of having wiring and appliances that can draw up to 30 amps before tripping the breaker. Will the wiring and circuity support that much current without damage? If not, then switch to a 15 or 20 amp breaker.
Replace the 30 Amp Breaker with a 15 Amp breaker.
30 amp
Yes.
No. The breaker must protect the circuit components such as wiring, outlets and switches that are connected to the breaker. Therefore if you have a 30 amp circuit as dictated by its components you need to protect it with a 30 amp or less breaker.
circuit breaker fuse
30 amp wired with AWG # 10 wire.
Remove the 30 amp double pole breaker and install at least one single pole 15 amp breaker. It is best if the other slot is not left open so if you have another single pole breaker of any size install it in the 2nd spot so it isn't open when you replace the cover on the panel. For your 15 amp circuit you need #14 gauge copper wire or larger with a hot, neutral, and ground. Your 30 amp circuit was probably wired with #10 gauge conductors. These will probably work on your 15 amp circuit but it may be difficult to connect #10 conductors to devices.
Yes. You should use 8 AWG wire from breaker to AC unit.
A 30 amp circuit breaker is needed unless the load is a motor circuit, then it has to be sized to 250 percent of the motors full load amps. For 30A circuit is needed breaker 30*1.25=37.5 --> 40A. If load is lamp or heater, then use breaker of group A or B. If load is motor, then use breaker of groupC or D (very hard start) or special safe breaker for motor - with variable amp setpoint. See related link also. By code you are only allowed 80% of the rating of a breaker. So 30x80%=24amps. 24 amps is the MAX allowed on a 30 amp breaker. You would need a 40amp breaker for a 30 amp circuit. 40x80%=32. So you would want a double pole 40amp breaker.
Not if it's functioning properly. The purpose of a circuit breaker is to shut off power if the circuit exceeds the rated power capacity of the wires. Don't plan to exceed the 30 Amp capacity of your house wiring; the results will be destructive.