0
What else can I help you with?
Can you run parallel number 6 wires to feed a 100 amp breaker?
Yes, you can run parallel wires to feed a 100 amp breaker. However, it is important to follow local electrical codes and regulations when doing so. It is recommended to consult with a licensed electrician to ensure the installation is done safely and correctly.
What is the maximum number of 100-W bulbs you can connwct in parallel in a 120-V home circuit without tripping the 20-A breaker?
You can connect a maximum of 24 100-W bulbs in parallel on a 120-V home circuit without tripping the 20-A breaker. This is calculated by dividing the total circuit wattage (2400 W) by the wattage of each bulb (100 W) to find the number of bulbs that can be safely connected.
Does a double 50 amp breaker make a 100 amp?
No, a double pole 50 amp breaker protects a 240 volt supply at 50 amps. The number that is on the handle of the breaker is the amperage that the breaker will trip at if an overload occurs on the circuit.
Can you have a 40 amp breaker with feeding a 100 amp shop panel. I have about 30 feet of 8 wires 4 between the two.?
Answer for USA, Canada and countries running a 60 Hz supply service.Yes, a 40 amp breaker can feed a 100 amp rated sub panel. The #8 wires are appropriate and the 4 wires consist of 2 hots, a neutral, and a ground. As a sub panel you keep the grounds and neutrals isolated from one another. If you are unsure of how to do this, consult a licensed electrician.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Can you run an additional breaker panel parallel to the existing one?
It is not in parallel. You put a breaker in existing panel and use that to feed the subpanel. The Amperage of this subfeed breaker should match the rating of the new panel. For example a 100A breaker might be typical. Remember that ground and neutral are only "bonded" at the main panel. Usually a subpanel has a means to separate the neutral and ground in a subpanel. Be careful since everything about doing this is dangerous.Another AnswerYes, you can have two breaker panels in parallel. If you had a 100 amp panel on a 200 amp service (or increase the size of the service, check with your power company on the size of your service, you could add a second 100 amp panel in parallel with the first. You can have up to 6 disconnects per service, but they must be located adjacent to each other or in the same enclosure. So either install the second panel beside the first or a 100 amp disconnect beside the first panel and feed out of the disconnect to the new panel located where you need it.
Can you run parallel number 6 wires to feed a 100 amp breaker?
Yes, you can run parallel wires to feed a 100 amp breaker. However, it is important to follow local electrical codes and regulations when doing so. It is recommended to consult with a licensed electrician to ensure the installation is done safely and correctly.
What is the maximum number of 100-W bulbs you can connwct in parallel in a 120-V home circuit without tripping the 20-A breaker?
You can connect a maximum of 24 100-W bulbs in parallel on a 120-V home circuit without tripping the 20-A breaker. This is calculated by dividing the total circuit wattage (2400 W) by the wattage of each bulb (100 W) to find the number of bulbs that can be safely connected.
What is the recommended replacement procedure for a faulty Pushmatic breaker 100 amp in a residential electrical panel?
To replace a faulty Pushmatic breaker 100 amp in a residential electrical panel, follow these steps: Turn off the main power supply to the panel. Remove the cover of the electrical panel. Identify the faulty Pushmatic breaker and switch it to the "off" position. Disconnect the wires connected to the breaker. Remove the faulty breaker from the panel. Install the new Pushmatic breaker in the same position. Connect the wires to the new breaker. Secure the breaker in place and replace the panel cover. Turn on the main power supply and test the new breaker to ensure it is working properly.
What is the maximum amperage capacity of the main breaker in a 100 amp sub panel with main breaker?
The maximum amperage capacity of the main breaker in a 100 amp sub panel with a main breaker is 100 amps.
Does a double 50 amp breaker make a 100 amp?
No, a double pole 50 amp breaker protects a 240 volt supply at 50 amps. The number that is on the handle of the breaker is the amperage that the breaker will trip at if an overload occurs on the circuit.
What size breaker do you use for a 100 amp sub panel?
A 100-A sub-panel would be fed from a 100-A breaker.
What is the maximum current capacity of a 100 amp circuit breaker?
The maximum current capacity of a 100 amp circuit breaker is 100 amps.
What is the maximum amperage capacity of a 100 amp Pushmatic breaker?
The maximum amperage capacity of a 100 amp Pushmatic breaker is 100 amps.
Can you have a 40 amp breaker with feeding a 100 amp shop panel. I have about 30 feet of 8 wires 4 between the two.?
Answer for USA, Canada and countries running a 60 Hz supply service.Yes, a 40 amp breaker can feed a 100 amp rated sub panel. The #8 wires are appropriate and the 4 wires consist of 2 hots, a neutral, and a ground. As a sub panel you keep the grounds and neutrals isolated from one another. If you are unsure of how to do this, consult a licensed electrician.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
What is the maximum amperage capacity of the main breaker in the electrical panel, specifically looking for a 100 amp main breaker?
The maximum amperage capacity of a 100 amp main breaker in an electrical panel is 100 amps.
Can you run an additional breaker panel parallel to the existing one?
It is not in parallel. You put a breaker in existing panel and use that to feed the subpanel. The Amperage of this subfeed breaker should match the rating of the new panel. For example a 100A breaker might be typical. Remember that ground and neutral are only "bonded" at the main panel. Usually a subpanel has a means to separate the neutral and ground in a subpanel. Be careful since everything about doing this is dangerous.Another AnswerYes, you can have two breaker panels in parallel. If you had a 100 amp panel on a 200 amp service (or increase the size of the service, check with your power company on the size of your service, you could add a second 100 amp panel in parallel with the first. You can have up to 6 disconnects per service, but they must be located adjacent to each other or in the same enclosure. So either install the second panel beside the first or a 100 amp disconnect beside the first panel and feed out of the disconnect to the new panel located where you need it.
What is the maximum amperage capacity of a 100 amp panel with main breaker?
The maximum amperage capacity of a 100 amp panel with a main breaker is 100 amps.
