answersLogoWhite

0


Best Answer

Yes you can, but it is all about distribution of the load. You still have a maximum limiting current of 150 Amps. So if you did use 100 amps on the sub-panel that would only leave 50 amps on the main. Since power usage is usually not constant and varies by day and situation, you just need to make sure the load is distributed so you don't start tripping breakers.

User Avatar

Wiki User

13y ago
This answer is:
User Avatar
More answers
User Avatar

AnswerBot

5mo ago

No, it is not recommended to use a 200 amp subpanel on a 100 amp branch circuit. The subpanel rating should not exceed the capacity of the branch circuit to prevent overloading and potential safety hazards. It is important to match the subpanel rating with the branch circuit capacity to ensure proper electrical function.

This answer is:
User Avatar

User Avatar

Wiki User

13y ago

no .If you max out the sub panel you have 100 amp in the main panel

This answer is:
User Avatar

User Avatar

Wiki User

12y ago

Yes as long as the combined current from both doesn't exceed the limit of the main.

This answer is:
User Avatar

User Avatar

Wiki User

12y ago

Yes, as long as you ensure that the feed to the subpanel is protected by a 100 Amp breaker and realize you can't overload the subpanel. Connect the subpanel with 3 AWG copper wire.

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Can you use a 200 amp subpanel on a 100 amp branch circuit?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Natural Sciences

What is the maximum amps for a sub panel?

The maximum amperage for a subpanel is typically determined by the size of the wire feeding it and the rating of the main panel. It is common for residential subpanels to be 100 or 200 amps, but it can vary depending on the specific installation and electrical code requirements. It's important to consult with a qualified electrician to determine the appropriate ampacity for your subpanel.


What is the current supply to a house amp?

The typical electrical service for a house in the US is 100 to 200 amps. This means the maximum current that can be safely drawn into the house at any given time is 100 to 200 amps. It's important not to overload the circuit as it can lead to electrical hazards.


You want to run power from your home you have a 200 amp in the house to a garage that you recently built you have 110 and 220 outlets The only 220 you plan on running is a small air compressor What?

You will need to install a subpanel in the garage with a capacity of at least 60 amps. This subpanel can be fed from the main panel in the house using appropriate gauge wires. Ensure that the 220V outlet for the air compressor is connected to the subpanel. The 110V outlets can be connected to the subpanel as well, distributing power as needed.


How much you can use in 200A breaker?

200. Although you cannot exceed current ratings on any branch circuit without tripping that circuit. You need to make sure that you do not exceed 160 continuous load amps to meet NEC requirements of not overloading a breaker to more than 80% under continuous load.


200 amp main and would like to add another 100 amp service in another room how can you do this?

To add another 100 amp service in another room, you would need to install a subpanel. This involves running a new electrical line from the main panel to the new location, installing the subpanel, and connecting the new circuits to it. It's important to ensure that the overall load on the main panel does not exceed its capacity with the addition of the new subpanel. Consulting a licensed electrician is recommended to ensure the work is done safely and up to code.

Related questions

How do I add new circuits to an 100 watt electrical box from the 1970'sIt has two open slots on the bottom and should I add a subpanel or upgrade the whole box I am disabled and have ltd resources?

It depends on what you are adding for a load. There is nothing wrong with what you have, but if you have more than two circuits to add, a subpanel is your answer if the loads are lighting or other small stuff. Pricewise and ease of installation equals a subpanel. If adding larger loads, an upgrade to 200 amps is necessary.


Can I use 200 watt siren if originally my unit come with 100 watt siren?

It depends on the circuit that controls the siren. The circuit may be designed for only a 100 watt device and by doubling the current through the circuit, the circuit may be destroyed.


What is 100 percent of 200?

100 is 50% of 200.


What is 158 rounded to nearest 100?

200


What is 137 rounded to the nearest hundred?

100


What pecent of 100 is 200?

It is: 200/100 times 100 = 200%


What is 165 rounded to the nearest hundred?

200


What is 200 divided by 2?

100


What is 100 plus 200?

200 + 100 = 300


What the answer of the LCM of 100 and 200?

The LCM is 200.


What is 237 rounded to the nearest 100?

It is: 200


WHAT 100 ADD 100?

200