0
What else can I help you with?
Can you use aluminum service cable to feed a sub panel?
Yes, as long as it has the necessary ampacity for the load and is properly fastened at each terminal. For example, we have a 4/0 aluminum cable feeding our 200 A subpanel 120 feet away.
What size wire is needed to feed a 125 amp sub panel from a 200 amp panel less than 200 wire feet away?
For a 125 amp sub panel located less than 200 feet away from a 200 amp panel, you would typically use a 2 AWG copper wire or 1/0 AWG aluminum wire to safely carry the current load. It's important to follow local electrical codes and regulations when selecting the wire size.
What size service cable for 100 amp main panel 100 feet away?
For a 100 amp main panel located 100 feet away, it is recommended to use a 2/0 copper or 4/0 aluminum service cable to ensure proper voltage drop and capacity for the distance. Consult with a licensed electrician to determine the specific requirements based on local codes and conditions.
What size wire do I need for a 60 amp service either 750 feet or 500 feet away?
It depends on the supply voltage because at that distance the size of the wire is calculated on the volt-drop which is 5% of the supply voltage, or 3% in some countries. The allowable resistance equals the volt-drop divided by the current, then you can use wire tables to find the wire size, remembering that a supply needs 2 wires which are in series so that their resistances add. <<>> To answer this question a voltage value has to be stated. This is due to the higher the voltage the lower the current on a specific load. The lower the current, the smaller the wire size can be.
What size wire do you need for 50 amp sub panel about 200 feet away?
Well, honey, for a 50 amp sub panel 200 feet away, you're gonna need a 6-gauge wire. Anything smaller and you'll be playing with fire, and not in a fun way. So do yourself a favor and splurge on that thicker wire to avoid any potential disasters down the line.
Can you use aluminum service cable to feed a sub panel?
Yes, as long as it has the necessary ampacity for the load and is properly fastened at each terminal. For example, we have a 4/0 aluminum cable feeding our 200 A subpanel 120 feet away.
What size wire is needed to feed a 125 amp sub panel from a 200 amp panel less than 200 wire feet away?
For a 125 amp sub panel located less than 200 feet away from a 200 amp panel, you would typically use a 2 AWG copper wire or 1/0 AWG aluminum wire to safely carry the current load. It's important to follow local electrical codes and regulations when selecting the wire size.
What size service cable for 100 amp main panel 100 feet away?
For a 100 amp main panel located 100 feet away, it is recommended to use a 2/0 copper or 4/0 aluminum service cable to ensure proper voltage drop and capacity for the distance. Consult with a licensed electrician to determine the specific requirements based on local codes and conditions.
What gauge wire to use for direct burial for a garage that is 400 feet from your house?
Depends on the size of the sub-panel in that garage. If you are installing a 60 amp sub-panel 400 feet away from the main service panel then use AWG # 4.
What is the recommended wire size for a 60 amp sub panel located 100 feet away?
For a 60 amp sub panel located 100 feet away, it is recommended to use a 6-gauge wire size to ensure proper electrical conductivity and safety.
What size aluminum wire to feed 125 Amps 220 volt a distance of 175' and what size ground?
A 3/0 aluminum conductor will limit the voltage drop to3% or less when supplying 125 amps for 175 feet on a 220 volt system. If the 125 amp load is a sub distribution panel that is not going to be fully loaded to 125 amps then using the exact connected load, which might be smaller than 125 amps will effect the wire sizing. The grounding conductor for that size distribution panel is #6 bare copper.
What size wire to run 250 feet away 60 amp sub panel?
Re Question with the voltage that you will be using.
Where is the kick panel on a 1998 Dodge Dakota?
it is the plastic panel to the left of your feet on the drivers side and to right side of your feet on the passengerside.
How many amps can a 8 gauge wire run coming from the ditribution panel to the sub panel 25 feet away?
A #8 copper wire with an insulation factor of 75 or 90 degrees C is rated at 45 amps.
How does his feet help him?
move and feed
How many square feet is a 4'X10' Panel?
40 approximate square feet!
What are the features of leg press exercise equipment?
A leg press consists of a bench that a person lays back against, a panel where the feet are placed, and a weight. A person would lay back and use their feet to push the weight away from their body.
