answersLogoWhite

0

There should be two wires in the box, black and white and possibly a bare one depending on the age of the wiring in the house. The fixture has two screws on the base. One wire goes on each screw. If there are short wires on the fixture, black to black and white to white. If there is a bare ground wire in the house box, it attaches to the body of the fixture. If there is no ground screw on the fixture, do not worry about it.

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Natural Sciences

How do you wire a series of recessed lights to a single switch when the power goes to the lights first?

If you already know how to put one fixture on a 3-way, just connect white-to-white and black-to-black from one light to the next. If you're changing from a single switch to the 3-way, the exact wiring will depend on whether the power comes from the breaker box to the switch or the existing fixture. I'll assume you're starting from scratch or have the power going to the fixture. You need #15 two-wire with ground and #15 three-wire with ground romex. Run two-wire from the breaker box to the first light fixture. Pull a another two-wire from this box to switch A and a three-wire between the switches. String two-wire from the first light to the second, second to third, etc. In the first box, connect white from source to the white fixture wire and the white going to the second box; black from source to the black to switch A; and the black fixture wire to both the white to switch A and the black to the next fixture. At each of the other 5 fixtures, connect all white to white and black to black (three pair in each box except the last one). At switch A, connect the white from the fixture to the common (center) connector and the black directly to the black going to switch B. The red and white wires going to switch B are connected to the two outside connectors of switch A. At switch B, the black goes to the common connector and the red and white to the outside connectors. At each box, connect all the bare wires (second ground) to each other and to the fixture or box. Now turn the power back on. If all the connectors are tight, power should follow the black wires from source past the fixture and switch A to switch B. From there it will go through one or the other of the travellers and, if switch A is in the same position as B, up the white switch leg to the fixtures, turn on all the lights and go back to ground.


Have 3 lights Power to light 1 Need to connect light 2 then light 3 then down to single pole switch How do you wire?

You would wire the switch to the first light. Code says to break the black or power side of the circuit. Connect the white to the light. Take the black down to the switch on the black wire and back to the light on the white. This is a line of wire from the light to the switch. From the first light, take the white and the return white from the switch to the second with another run of wire. This will be regular black white with ground. White to white and at the first light the return line from the switch is white but hook to the black to the second light. Second light to third just continues the two wires. Black to black, white to white. I think this is clear enough to follow. If not, ask again.


How do you wire two outside light sensing motion porch lights that are controlled from one switch with each light having a white black ground and optional red wire?

Connect the black wire from the switch to the black wires of both lights. Connect the white wires together. Connect the red wire, if used for the motion sensor, to the black wires on the lights. Connect all ground wires together and to the ground terminal on the switch. Make sure to turn off power before connecting any wires for safety.


How do you connect multiple lights to one switch starting at the light?

To connect multiple lights to one switch starting at the light, you will need to run a cable from the first light fixture to the switch. Connect the hot wire to the switch, along with a pigtail wire to connect to each light. Then connect each light fixture to the pigtail wire to create a parallel circuit. Make sure to follow proper safety precautions and consult a professional if needed.


How do you wire a light and switch with the 2 wire old romex?

To wire a light and switch using 2-wire Romex, connect the black wire to the brass screw on the switch, the white wire to the light fixture, and the white wire to the silver screw on the switch. Make sure to cap the unused wire at both ends for safety. Be sure to turn off the power before starting and consult a professional if you are unsure.

Related Questions

How do you wire a series of recessed lights to a single switch when the power goes to the lights first?

If you already know how to put one fixture on a 3-way, just connect white-to-white and black-to-black from one light to the next. If you're changing from a single switch to the 3-way, the exact wiring will depend on whether the power comes from the breaker box to the switch or the existing fixture. I'll assume you're starting from scratch or have the power going to the fixture. You need #15 two-wire with ground and #15 three-wire with ground romex. Run two-wire from the breaker box to the first light fixture. Pull a another two-wire from this box to switch A and a three-wire between the switches. String two-wire from the first light to the second, second to third, etc. In the first box, connect white from source to the white fixture wire and the white going to the second box; black from source to the black to switch A; and the black fixture wire to both the white to switch A and the black to the next fixture. At each of the other 5 fixtures, connect all white to white and black to black (three pair in each box except the last one). At switch A, connect the white from the fixture to the common (center) connector and the black directly to the black going to switch B. The red and white wires going to switch B are connected to the two outside connectors of switch A. At switch B, the black goes to the common connector and the red and white to the outside connectors. At each box, connect all the bare wires (second ground) to each other and to the fixture or box. Now turn the power back on. If all the connectors are tight, power should follow the black wires from source past the fixture and switch A to switch B. From there it will go through one or the other of the travellers and, if switch A is in the same position as B, up the white switch leg to the fixtures, turn on all the lights and go back to ground.


How to wire a light switch properly?

To wire a light switch properly, first turn off the power to the circuit. Then, connect the black wire from the power source to the black wire on the switch. Next, connect the white wire from the power source to the white wire on the switch. Finally, connect the ground wire to the green screw on the switch. Make sure all connections are secure before turning the power back on.


How do you hook up a light switch?

To hook up a light switch, first turn off the power to the circuit. Then, connect the black wire from the switch to the black wire from the power source, and the white wire to the white wire. Finally, connect the ground wire to the green screw on the switch. Secure the switch in place and turn the power back on to test the connection.


How do I wire a light switch to a light?

To wire a light switch to a light, first turn off the power to the circuit. Connect the black wire from the switch to the black wire from the light. Connect the white wire from the switch to the white wire from the light. Finally, connect the ground wire from the switch to the ground wire from the light. Secure all connections with wire nuts and cover with electrical tape. Turn the power back on and test the switch to ensure it is working properly.


How do you wire up a light switch?

To wire up a light switch, you need to turn off the power, remove the old switch, connect the wires to the new switch (usually black to black, white to white, and ground to ground), and then secure the switch in place. Finally, turn the power back on to test the switch.


How do you wire an outlet switch combo?

To wire an outlet switch combo, first turn off the power to the circuit. Connect the black wire to the brass screw on the switch, the white wire to the silver screw, and the ground wire to the green screw. Then, connect the black wire from the outlet to the brass screw on the switch, the white wire to the silver screw, and the ground wire to the green screw. Finally, connect the remaining black and white wires to the corresponding screws on the outlet. Make sure to secure all connections and test the switch and outlet before turning the power back on.


How do you wire an electrical switch?

To wire an electrical switch, first turn off the power to the circuit. Connect the black wire from the power source to one terminal on the switch, and connect the black wire going to the light fixture to the other terminal. Connect the white wires together and the ground wires together. Secure the switch in the electrical box and turn the power back on to test the switch.


How can I connect a wire switch to a light fixture?

To connect a wire switch to a light fixture, first turn off the power to the circuit. Then, connect the black wire from the switch to the black wire from the light fixture using a wire connector. Next, connect the white wires together and the ground wires together. Finally, secure all connections with electrical tape and mount the switch and light fixture as needed.


How do you properly wire a single light switch?

To properly wire a single light switch, you need to turn off the power, remove the old switch, connect the wires to the new switch (usually black to black, white to white, and ground to ground), and then secure the switch in place before turning the power back on.


Have 3 lights Power to light 1 Need to connect light 2 then light 3 then down to single pole switch How do you wire?

You would wire the switch to the first light. Code says to break the black or power side of the circuit. Connect the white to the light. Take the black down to the switch on the black wire and back to the light on the white. This is a line of wire from the light to the switch. From the first light, take the white and the return white from the switch to the second with another run of wire. This will be regular black white with ground. White to white and at the first light the return line from the switch is white but hook to the black to the second light. Second light to third just continues the two wires. Black to black, white to white. I think this is clear enough to follow. If not, ask again.


How to wire a single pole switch?

To wire a single pole switch, first turn off the power to the circuit. Connect the black wire from the power source to the brass screw on the switch. Connect the black wire going to the light fixture to the other brass screw. Finally, connect the white wires together with a wire nut and connect the ground wire to the green screw on the switch. Turn the power back on and test the switch.


How can I wire a ceiling fan with a light switch using a diagram?

To wire a ceiling fan with a light switch, follow these steps: Turn off the power to the circuit at the breaker box. Install the ceiling fan bracket to the ceiling. Connect the fan wires to the corresponding wires in the ceiling box (usually black to black, white to white, and green to ground). Connect the light kit wires to the corresponding wires in the ceiling box (usually blue to black and white to white). Install the fan blades and light kit. Install the light switch and connect the wires (usually black to black, white to white, and ground to ground). Turn the power back on and test the fan and light switch. For a visual guide, refer to the diagram below: Diagram of ceiling fan wiring with light switch