answersLogoWhite

0

The answer is likely NO. I assume you're talking about a 60 amp subpanel. To upgrade to a 100 amp, the wire size will need to be increased. (replaced with the correct size) This is not a job for amateurs but should be done by a qualified electrician. The typical size wire employed for a 60 amp supply is # 6 awg, whereas the minimum wire size for 100 amp is # 3 awg (which is larger).

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Natural Sciences

What is the largest sub panel you can install off from a 60 amp main panel fed by 100 amp service?

If what you state in this question is accurate this is an illegal installation. A 100 amp service can not have any equipment connected to it less that that of the service size. The 60 amp main panel must be a 100 amp panel to be a legal installation.


Can work wire for 100 amps use for 60 amps circuit?

If you have 100 amp wire, you can use it for a 60 amp circuit, or for any circuit of 100 amps or less. But if you have a 60 amp circuit, 60 amp wire is thinner and cheaper than 100 amp wire.


You have 60 amp service and want change to 100 amps you have a 200 amp panel with breakers can you use this for 100 amp service?

In short Yes. However, you must change the main disconnect (breaker) to a 100 amp disconnect. Your local home improvement center may have what you need, or you may have to go to a wholesale dealer to get the main. You will also need to verify that the conductors from the utility and all associated distribution system will accommodate the additional load from 60A to 100A. Always be careful and remember that most home fires are started by electrical failure. Electricity can also cause severe personal injury, including death. If you have any doubt, call an electrical contractor. This type of change to an electrical system should be attempted by only a very experienced homeowner. Your local jurisdiction may also require a permit and inspections be performed. Your local utility may also have additional requirements. SAFETY FIRST and ALWAYS! Hope this helps! Terry


A 60 amp electrical service panel at a 2800 square foot home would be?

If it was preinstalled, it may have been adequate at the time of installation. It depends on the power requirements of the home. If this is a new install, the NEC has a minimum of 100A for service equipment. To be honest, I would install 200A minimum to allow for future expansion.


What do they replace when upgrading from 60 amp to 100amp?

Usually you just have to replace the electric panel and maybe the electric meter and entrance cable. It would be unusual, but the power company may want to replace the cable from the local transformer to your house.

Related Questions

What is the largest sub panel you can install off from a 60 amp main panel fed by 100 amp service?

If what you state in this question is accurate this is an illegal installation. A 100 amp service can not have any equipment connected to it less that that of the service size. The 60 amp main panel must be a 100 amp panel to be a legal installation.


What is the Hz rating on 100 Amp household service?

60 Hz in North America, 50 Hz in Europe.


How do you run a 100 amp subpanel off a 60 amp subpanel?

To run a 100 amp subpanel from a 60 amp subpanel, you first need to ensure that the 60 amp subpanel is capable of handling the additional load. Install a double-pole 60 amp breaker in the 60 amp subpanel and connect it to the feeder wires that will supply the 100 amp subpanel. However, since the 60 amp subpanel cannot provide full capacity to the 100 amp subpanel, you should limit the load on the 100 amp subpanel to a maximum of 60 amps. It's also advisable to consult with or hire a licensed electrician to ensure compliance with local electrical codes and safety standards.


What is the recommended wire size for a 60 amp service?

The recommended wire size for a 60 amp service is typically 6-gauge copper wire.


Can work wire for 100 amps use for 60 amps circuit?

If you have 100 amp wire, you can use it for a 60 amp circuit, or for any circuit of 100 amps or less. But if you have a 60 amp circuit, 60 amp wire is thinner and cheaper than 100 amp wire.


You have 60 amp service and want change to 100 amps you have a 200 amp panel with breakers can you use this for 100 amp service?

In short Yes. However, you must change the main disconnect (breaker) to a 100 amp disconnect. Your local home improvement center may have what you need, or you may have to go to a wholesale dealer to get the main. You will also need to verify that the conductors from the utility and all associated distribution system will accommodate the additional load from 60A to 100A. Always be careful and remember that most home fires are started by electrical failure. Electricity can also cause severe personal injury, including death. If you have any doubt, call an electrical contractor. This type of change to an electrical system should be attempted by only a very experienced homeowner. Your local jurisdiction may also require a permit and inspections be performed. Your local utility may also have additional requirements. SAFETY FIRST and ALWAYS! Hope this helps! Terry


Can 700 watt microwave compatible for 60 amp service?

As long as the voltages match a 60 amp service will handle a 700 watt microwave. The microwave will only draw A = W/V, A = 700/120 = 5.8 amps.


What is the minimum service size for a 225amp residential service?

A 200 amp service panel with a 60 amp sub-panel.


How do a change 60 to a percent?

change 60 to a percent = 6000%60 * 100% = 6000%


What does a 60 amp fuse service in a 2004 Ford Taurus?

The 2 - 60 amp maxi fuses in the power distribution box in the engine compartment are for the passenger compartment fuse panel


A 60 amp electrical service panel at a 2800 square foot home would be?

If it was preinstalled, it may have been adequate at the time of installation. It depends on the power requirements of the home. If this is a new install, the NEC has a minimum of 100A for service equipment. To be honest, I would install 200A minimum to allow for future expansion.


What current rating is used in house service wiring today?

New homes being built today usually have a 200 amp 42 circuit distribution panel installed. Older homes from 20 to 30 years ago had 100 amp 24 circuits installed and this was thought to be a vast improvement over the 60 amp services that it replaced. There are more and higher amperage appliances these days and a 42 circuit panel can get used up very quickly. If your talking about total current service to homes. Average size house is usually 100 amp service.