0
the wires coming off double pole will give you 240 volts,110 each the black and white hook to these,doesn`t matter which way,ground to ground
Ground is always ground, Black and white are your two "hots." You will need a dedicated circuit, you cannot run this off existing 120V wiring. A 15A 240V circuit should be more than sufficient. If this is a permanent instalation you can use 14/2 wire as you normally would, and wire it as you normally would with the exception of the 240V breaker. If you install switches, timers, etc. Make sure they are all rated for 240V. Remember, you can't just mix-and-match between 120 and 240V. 240 appliances will not run on 120 and 120 appliances will burn up on 240.
What else can I help you with?
Why does a light turn when you place black to black and white to ground wire?
You don't say "turn off" or turn on". Light should be connected black to black and white to white and ground to ground. If you connect white to ground it will work, but you are then using the ground wire for an unintended purpose. Neutral is bonded to Ground at the panel. Current on ground wire could cause ground loops and may cause GFCI to trip if you have them in your house.
Is 480 lumens good for flood light?
480 lumens may not be sufficient for a flood light, as flood lights are typically used for wide area illumination and require higher lumen output. Consider a flood light with a higher lumen rating for better coverage and brightness.
How do you wire flood lights to existing lights?
You would need to check for other lights on the same circuit or switch, but it would seem to me that you have power coming into the box (black and white) and a power out going to another box or light. You would use wire nuts to connect the black and white wires from your floodlight to the existing ones.
If there are two black and one white wire in ceiling light do I need to use both black for the switch to work?
If there are two black wires, it's possible that it was wired for a ceiling fan and that one of the wires is for the fan part while the other is for the light part. If so, one of the black wires may be switched while the other is always "on." Normally black is "hot" and white is "neutral" (NOT ground... ground is usually green).
How do you hook up outside light fixture that has black white green to house wiring with only black and white?
If your house wiring is encased in armoured (metal) sheathing back to the panel, then you can secure the green ground to the ground screw in the box. Make sure the armoured cable connector is tight on the box. This should ground the light back to the panel. If you are on "knob & tube" I would suggest thinking about re-wiring the house.
How many lights are in the Malibu 4-Light Black Metal Flood Kit?
The Malibu 4-Light Black Metal Flood Kit are made up of Four 50 Watt floodlights.
Does the Malibu 4-Light Black Metal Flood Kit come with bulbs?
Yes, the Malibu 4-Light Black Metal Flood Kit comes with bulbs Low Voltage kit.4-CL1, 50 watt floodlights,100 Ft. cable etc.
What is the best type of reverse light to use spot or flood light?
flood.
Why does a light turn when you place black to black and white to ground wire?
You don't say "turn off" or turn on". Light should be connected black to black and white to white and ground to ground. If you connect white to ground it will work, but you are then using the ground wire for an unintended purpose. Neutral is bonded to Ground at the panel. Current on ground wire could cause ground loops and may cause GFCI to trip if you have them in your house.
Can you run power from a light fixture to another light fixture?
Yes. Connect Black to Black, White to White and bare ground wires together.
How do you wire 12volt holagen light to battery?
Red is positive black is ground.
When you have a black brown and green wire on a tail light pig tail is the black one ground?
Usually, yes.
Is 480 lumens good for flood light?
480 lumens may not be sufficient for a flood light, as flood lights are typically used for wide area illumination and require higher lumen output. Consider a flood light with a higher lumen rating for better coverage and brightness.
What is the difference between a narrow flood light and a spot light?
A "spot" is more narrow than a "narrow flood".
What is the Electrical diagram for fuel pump 96 dodge ram van B350?
Dark Green / Black: Fuel Pump Motor + [To ECU]Black: Fuel Pump Motor Ground [TO GROUND]Black / White: Sensor Grd [TO GROUND]Dark Blue: Fuel Gauge Signal [TO INSTRUMENT CLUSTER]Black / Light Blue: Sensor Return [TO VARIOUS]Light Blue / Black: Low Fuel Out [TO ECU]
What color wires in the trunk of a 2001 Buick Lesabre Custom are the power and ground for the reverse lights?
power = light green ground = black
How much energy does an LED light consume?
An LED flood light uses a fraction of the power of a traditional flood light. It uses less then 1/4 the the power. They also last much longer the traditional flood lights.
