0
How do you wire a 240V stove plug if old stove was hard wired and had 4 wires Black red white and ground coming from the wall are three wires Black red and a shield wire is the shield wire the neutral?
Wiki User
∙ 18y ago
Shield is ground. White is Neutral, center tap of the transformer from the power company.
Wiki User
∙ 18y ago
The shield wire is not the neutral wire. You will need to connect the black and red wires to the hot terminals of the stove plug and the shield wire to the ground terminal. However, it is advisable to consult a licensed electrician to ensure proper and safe installation.
Add your answer:
Earn +20 pts
How do you put on a four prong outlet on a roper electric dryer?
Black & Red are hot, and White is neutral. If it has no place to connect neutral connect neutral to ground.
What is the color of live wire neutral wire and ground wire in Bangladesh.?
In Bangladesh, the live wire is typically red, brown, or black; the neutral wire is typically blue or black; and the ground wire is typically green or green with a yellow stripe. It is important to consult with a local electrician or electric code regulations for accurate information.
Should the black wire be bonded to the ground?
It depends on the color coding standards for what country you are in. In the US, the answer is no. The Neutral (white wire) is grounded at the service entrance to the building. The black wire should have roughly the same voltage to the neutral and to the ground. Something to be aware of: If you are using a meter and checking for continuity between the black wire and ground, it may tell you that they have continuity if the breaker is on.
You have two white wires and two black wires which one is the ground?
black wire is hot wire .And the white is the common or white is ground. Depends on what your talking about in an outlet or car battery. In a outlet the ground wire is green or bare copper. neutral is red and hot is black (I remember it by hot can kill you so black is death) if I am not mistaken. As for a car battery i think it's the opposite red is hot and black is neutral.
What colour wire goes to the breaker using 12-2 wire?
For a typical 12-2 wire, the black wire is the "hot" wire that connects to the breaker, the white wire is the neutral wire that connects to the neutral bus bar, and the bare copper wire is the ground wire that connects to the ground bus bar in the circuit panel.
There are only 3 phases that come into house main fuse box so where does ground and neutral come from?
It is very rare to have three-phase electricity coming into a residence. One of the wires is probably the neutral (It will be white or black with white stripes.) The ground comes in from a ground rod near the main, and connects to the ground coming from the meter, AND (If the main fuse box is the first disconnecting means,) the neutral and ground bars have to be bonded together in the box.
How do you put on a four prong outlet on a roper electric dryer?
Black & Red are hot, and White is neutral. If it has no place to connect neutral connect neutral to ground.
What is the color of live wire neutral wire and ground wire in Bangladesh.?
In Bangladesh, the live wire is typically red, brown, or black; the neutral wire is typically blue or black; and the ground wire is typically green or green with a yellow stripe. It is important to consult with a local electrician or electric code regulations for accurate information.
How do you hook up the distribution panel box with red white black and ground wires?
Without more information that appears to be a 240 volt circuit. Red & black would connect to the 240 volt breaker, white connects to the neutral bar, and ground conductor from the ground rods or ground plate connects to the neutral bar. Make sure that the bonding screw is in the neutral bar and it is screwed through to bond the distribution panel enclosure to the neutral bar.
Should the black wire be bonded to the ground?
It depends on the color coding standards for what country you are in. In the US, the answer is no. The Neutral (white wire) is grounded at the service entrance to the building. The black wire should have roughly the same voltage to the neutral and to the ground. Something to be aware of: If you are using a meter and checking for continuity between the black wire and ground, it may tell you that they have continuity if the breaker is on.
What colour wire is negative - green or black?
Most likely your "purple" was once black, and is the negative; to verify, trace "purple" to ground, or touch the leads of an ohmmeter to purple and ground. You should get "0" ohms at the correct wire. This assumes a negative ground.
What is the Household wiring color code?
On a 110 volt circuit, Black is hot, White is neutral, Green or bare Copper is ground. . Connect Black to the gold screw, White to the silver screw, and bare copper ground to the Green ground screw on the receptacle. On a 220 Volt circuit Black & Red are both hot, each carrying 110 volts for a total of 220. White is Neutral and ground is Green or bare copper.
How do you wire a wire to a wire?
If you are connecting 120 volts, you connect the black wire to the breaker, white wire to the neutral bar, and ground wire to the ground bar. If you are connecting 240 volts connect the black & white wires to the breaker, & ground wire to the ground bar.
If you have an air solenoid valve DC and the wires are Green Black and White. Which one is positive and negative?
Green= Ground Black = live White = Neutral
Single Phase 240 120 Volts AC a test meter placed across black wire and Ground wire will read what?
Answer for USA, Canada and countries running a 60 Hertz supply service.A test meter across black and ground in a 120/240 split phase system should read about 120 volts. Note, however, that ground is not the correct reference point; neutral is the correct reference point, and the meter should be connected across black and white, or red and white, or red and black. This is because the ground connection is a protective earth ground, not intended to carry current. Since ground and neutral are tied together at the distribution panel, you might expect them to have no potential difference, but impedance in the conductors will result in a voltage drop across neutral, biasing the voltage seen between hot and ground, as opposed to hot and neutral.
Is green ground in an extention cord?
Yes, the green conductor is the colour of the ground wire in an extension cord. The black wire is dedicated to be the "hot" and the white conductor is the neutral.
You have two white wires and two black wires which one is the ground?
black wire is hot wire .And the white is the common or white is ground. Depends on what your talking about in an outlet or car battery. In a outlet the ground wire is green or bare copper. neutral is red and hot is black (I remember it by hot can kill you so black is death) if I am not mistaken. As for a car battery i think it's the opposite red is hot and black is neutral.
