0
What else can I help you with?
Will a 2 pole 60 amp ITE Gould or Westinghouse breaker replace a 2 pole 60 amp T and B unit?
Yes, a 2 pole 60 amp ITE Gould or Westinghouse breaker can replace a 2 pole 60 amp T and B unit as long as they have the same voltage rating and fit properly in the panel. It is important to make sure that the replacement breaker is compatible with your specific panel model.
Can you change 30 amp to 60 amp?
Changing a 30 amp circuit to a 60 amp circuit involves more than just swapping out the breaker. It would require upgrading the wiring to handle the increased current capacity, as well as ensuring that all components connected to the circuit can safely handle the higher amperage. It is crucial to consult with a qualified electrician to assess the feasibility and safety of such an upgrade, as it may involve significant modifications to the electrical system.
Can you put a 60 amp fuse in a 60 amp disconnect?
Yes, you should use a 60 amp fuse in a 60 amp disconnect to ensure proper protection and compatibility with the electrical system. Using the correct amperage fuse helps prevent electrical hazards and keeps the circuit operating safely.
Can you feed a 60 amp sub panel from another 60 amp sub panel?
Yes, you can feed a 60 amp sub panel from another 60 amp sub panel as long as the total connected load does not exceed 60 amps. Make sure to properly size the wire and protect the circuits with appropriate breakers to ensure safe operation of the sub panel.
Do you have to change from 60 amp to 100 amp service?
The answer is likely NO. I assume you're talking about a 60 amp subpanel. To upgrade to a 100 amp, the wire size will need to be increased. (replaced with the correct size) This is not a job for amateurs but should be done by a qualified electrician. The typical size wire employed for a 60 amp supply is # 6 awg, whereas the minimum wire size for 100 amp is # 3 awg (which is larger).
Will a 2 pole 60 amp ITE Gould or Westinghouse breaker replace a 2 pole 60 amp T and B unit?
Yes, a 2 pole 60 amp ITE Gould or Westinghouse breaker can replace a 2 pole 60 amp T and B unit as long as they have the same voltage rating and fit properly in the panel. It is important to make sure that the replacement breaker is compatible with your specific panel model.
How do you run a 100 amp subpanel off a 60 amp subpanel?
To run a 100 amp subpanel from a 60 amp subpanel, you first need to ensure that the 60 amp subpanel is capable of handling the additional load. Install a double-pole 60 amp breaker in the 60 amp subpanel and connect it to the feeder wires that will supply the 100 amp subpanel. However, since the 60 amp subpanel cannot provide full capacity to the 100 amp subpanel, you should limit the load on the 100 amp subpanel to a maximum of 60 amps. It's also advisable to consult with or hire a licensed electrician to ensure compliance with local electrical codes and safety standards.
How do you convert amp hours to amp minutes?
Divide by 60.
What is the maximum amperage capacity of a 60 amp circuit breaker?
The maximum amperage capacity of a 60 amp circuit breaker is 60 amps.
What is the maximum current capacity supported by a 60 amp breaker?
A 60 amp breaker can support a maximum current capacity of 60 amps.
Can you change 30 amp to 60 amp?
Changing a 30 amp circuit to a 60 amp circuit involves more than just swapping out the breaker. It would require upgrading the wiring to handle the increased current capacity, as well as ensuring that all components connected to the circuit can safely handle the higher amperage. It is crucial to consult with a qualified electrician to assess the feasibility and safety of such an upgrade, as it may involve significant modifications to the electrical system.
What type of electrical outlet is required for a device that needs a 60 amp plug?
A device that needs a 60 amp plug requires a special type of electrical outlet called a 60 amp outlet.
What size breaker is used for a 5 ton 34 amp minimum 60 amp maximum?
60 amp using AWG # 6 copper for branch circuits.
Can you put a 60 amp fuse in a 60 amp disconnect?
Yes, you should use a 60 amp fuse in a 60 amp disconnect to ensure proper protection and compatibility with the electrical system. Using the correct amperage fuse helps prevent electrical hazards and keeps the circuit operating safely.
What is the maximum current rating of a 2 pole 60 amp breaker?
The maximum current rating of a 2 pole 60 amp breaker is 60 amps.
What information can I find in the 60 amp wire size chart?
The 60 amp wire size chart provides information on the appropriate wire gauge or size to use for a 60 amp electrical circuit. It includes details such as the wire gauge, maximum current capacity, and insulation type suitable for a 60 amp load.
What gauge wire should be used for a 60 amp breaker?
For a 60 amp breaker, a 6-gauge wire should be used.
