0
If you're looking for a wire to cover all the areas use 10 guage. Very heavy but will handle most normal vehicle requirements except for extreme areas such as starter/battery cables (1 - 6 guage), and some stereo main amp feeds. You won't need 10 guage in a lot of applications (overkill) but it will cover most areas as I said. 16 guage is good for a lot of vehicle applications (lighting etc..). Check out the area of repair/installation and depending on the amperage needed you select you wiring. Below is a link to a chart you may find usefull. http://www.kayjayco.com/techPractical.htm
For a 10 amp load at 12 volts DC, a 16-gauge wire is typically recommended. This size wire can safely handle the current without significant voltage drop or heating issues. It's always best to consult the specific wire sizing guidelines or a professional electrician to ensure safety and efficiency.
Sure you can use 14gage wiring for a 12V system. Assuming you are talking about the wiring commonly used in homes referred to as Romex cable. This cable is rated for up to 600V and can be used for any voltage under 600. However the problem you run into is 14gage Romex cable is rated for 15A regardless of the voltage. If you were to use it for a 12V system you would be limited to only 180W. Considering that most 12V light bulbs are 40W this would allow you to power only 4 40W bulbs on a 14gage circuit.
A 12 Gauge wire will handle approximately 20-26 Amps regardless of the voltage. Higher amperage can be attained by using wire with insulation that can handle higher heat.
Add your answer:
Earn +20 pts
What gauge wire you would use to wire a 5kw heater hvac?
For a 5kW heater HVAC system, you would typically need to use 10-gauge wire to handle the current load safely. It's important to always consult the manufacturer's specifications or a licensed electrician to ensure you are using the correct wire gauge for your specific setup.
What amps is for 16 gauge wire?
10
What gauge of wire is needed for a baseboard heater 1000 watt 240 Volt 4.2 Amp?
For a baseboard heater that is 1000 watts and operates at 240 volts with a current draw of 4.2 amps, you would need to use 12-gauge wire. This gauge of wire is rated for up to 20 amps, providing a safe and sufficient electrical connection for your heater.
What gauge of wire to connect electric dryer?
You need a 3 conductor #10 cable. A #10 wire is rated at 30 amps.
What is ampere rating of 16 gauge wire at 120 volts?
For a 16-gauge wire at 120 volts, the ampere rating would typically be around 10-12 amps. However, it's important to consult the specific standards and guidelines provided by regulatory bodies like the National Electrical Code (NEC) to ensure safe and appropriate usage of the wire.
What is ampere rating of 10 gauge wire at 120 volts and at 240 volts?
30 amps.
What size copper wire do you need for 240 volts 16 amps at 150ft?
10 gauge
What gauge wire would you need 5600 watts 240 volts 23.3 amps?
AWG # 10.
What gauge wire is required for 25 amps over 100 ft at 240 volts?
10 AWG copper.
What gauge wire you would use to wire a 5kw heater hvac?
For a 5kW heater HVAC system, you would typically need to use 10-gauge wire to handle the current load safely. It's important to always consult the manufacturer's specifications or a licensed electrician to ensure you are using the correct wire gauge for your specific setup.
What size wire for 10kw 240 volt?
10 mm2 cross section should be sufficient (#6 wire?)
What gauge wire can handle 28 amps?
10 guage
If I have 150ft of 10 gauge wire with 60 amp service how many amps and watts do I have available at the end of the line?
10 gauge wire will only run up to 30 amps
What is the amperage limit of 10 gauge solid wire?
Typically 30 amps.
What amps is for 16 gauge wire?
10
How many amps is a 16 gauge wire 12 volts rated for?
12 ga, 20 amp. 14 ga, 15 amp. 16 ga, 10 amp.
Wire size for 500 feet distance 120 volt 20 amps?
The American Wire Gauge code table shows 8 gauge safe for 24 Amps, 10 Gauge for 15 Amps. If the circuit is going to be used at capacity (2400 Watts in this case), 8 or 10 gauge is the minimum, if load is constant, use 8 gauge. Voltage ability of the wire is dependent on the insulation thickness and material. So 20 amps at 120 Volts is 2400 watts of power, and 20 amps at 12 volts is 48 watts of power. Both would require the same gauge of wire, but the higher voltage would need better insulation. <<>> This is a voltage drop question. A #1 copper conductor will limit the voltage drop to 3% or less when supplying 20 amps for 500 feet on a 120 volt system.
