0
Several different factors must always be considered when deciding the correct wire size to use:
- amperage, which is the current to be supplied, measured in amps?
- length of wire-run?
- installation situation/site conditions?
- run inside a conduit?
- exposed to the air fixed to a wall?
- extreme heat?
- damp conditions?
- underground?
To get the right answers refer to the Wiring Codes or Regulations for your locality. (Town/State.)
<><><>
A #6 copper wire with an insulation factor of 75 or 90 degrees C is rated at 65 amps.
<<>>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
What else can I help you with?
What gauge wire would you use to wire a 120V 20A motor?
For a 120V 20A motor, you would typically use a 12-gauge wire to ensure it can handle the current without overheating. This wire size is suitable for the amperage and voltage to provide proper insulation and safe operation for the motor.
Can you use 8 gauge wire with a 50 amp breaker?
No, an 8 gauge wire is typically rated for a maximum of 40 amps. It is important to match the wire gauge with the appropriate amperage to prevent overheating and potential fire hazards. In this case, you would need to use a thicker wire gauge, such as 6 gauge, for a 50 amp breaker.
What is the max safe amps for 14 gauge wire?
The maximum safe amperage for 14 gauge wire is typically around 15 amps in most household wiring applications. Exceeding this amperage could lead to overheating of the wire and pose a fire hazard. It's important to always verify the specific requirements with the National Electrical Code or a qualified electrician for your specific application.
What can you use 10 gauge wire for?
ten gauge wire is used for high current circuits. in home wiring, 12 gauge wire is normally used. 12 gauge wire can carry a maximum of 20 amps. 10 gauge wire on the other hand, is larger and can carry more current. the maximum current capacity of a 10 gauge wire is around 30 amps. one would use this for a stove, hvac or other power hungry device's.
What gauge wire do you use for 15 amps 200 feet?
For a 15 amp circuit over 200 feet, it is recommended to use a 14-gauge wire to ensure proper voltage drop. This gauge wire will help maintain the integrity of the electrical supply over that distance.
What size USE wire is needed for 200 amps?
As a service entrance wire you need AWG # 3/0 gauge copper.
What gauge wire would you use to wire a 120V 20A motor?
For a 120V 20A motor, you would typically use a 12-gauge wire to ensure it can handle the current without overheating. This wire size is suitable for the amperage and voltage to provide proper insulation and safe operation for the motor.
What is amp rating of 14 gauge wire?
In normal residential use it is 20 Amps. That depends on alot of things such as the wire insulation, ambient temperature, etc. Standard NM 12/2 (Romex or equivalent, which is likely what you are asking as it is the primary type used to wire residential) is rated for 20 amps, 14 gauge is 15 amps, 10 gauge is 30 amps.
Can you use 8 gauge wire with a 50 amp breaker?
No, an 8 gauge wire is typically rated for a maximum of 40 amps. It is important to match the wire gauge with the appropriate amperage to prevent overheating and potential fire hazards. In this case, you would need to use a thicker wire gauge, such as 6 gauge, for a 50 amp breaker.
What is the proper size wire cord for a 12 amp vacuum sweeper 120 volt?
16 gauge is rated at 13 amps, but I would use 14 gauge which is rated at 15 amps just to be safe.
What is the max safe amps for 14 gauge wire?
The maximum safe amperage for 14 gauge wire is typically around 15 amps in most household wiring applications. Exceeding this amperage could lead to overheating of the wire and pose a fire hazard. It's important to always verify the specific requirements with the National Electrical Code or a qualified electrician for your specific application.
What gauge of wire must be used in homemade wind turbine?
You would need to know the maximum watts and voltage you could generate then go from there. In home use you use 12 gauge wire at 120 volts to handle up to 20 amps. 14 gauge for 15 amps. If you're operating in 12 volt it's a different ballgame.
What is the recommended gauge of wire to use for a 12 or 14 gauge wire?
The recommended gauge of wire to use for a 12 or 14 gauge wire is typically 10 gauge wire.
What size wire of suitable 13amp motor?
I would recommend you use AWG # 14 gauge which is rated at 15 amps.
What can you use 10 gauge wire for?
ten gauge wire is used for high current circuits. in home wiring, 12 gauge wire is normally used. 12 gauge wire can carry a maximum of 20 amps. 10 gauge wire on the other hand, is larger and can carry more current. the maximum current capacity of a 10 gauge wire is around 30 amps. one would use this for a stove, hvac or other power hungry device's.
What gauge wire do you use for 15 amps 200 feet?
For a 15 amp circuit over 200 feet, it is recommended to use a 14-gauge wire to ensure proper voltage drop. This gauge wire will help maintain the integrity of the electrical supply over that distance.
How many automotive amps can 30 foot strand of copper wire carry?
The number of automotive amps a 30-foot strand of copper wire can carry depends on the gauge (thickness) of the wire. For example, a 30-foot strand of 10-gauge copper wire can typically carry up to 40-50 amps for automotive use, while a 30-foot strand of 12-gauge wire might be limited to around 25-30 amps. It's important to consult wire ampacity tables and consider factors like temperature and voltage drop to ensure safe and effective performance.
