0
Attaching the wrong wires on a light fixture can lead to a circuit overload, short circuit, or damage to the fixture. It can also pose a safety hazard, increasing the risk of electric shocks or fires. It's important to always follow the manufacturer's instructions and seek professional help if you are unsure.
The danger is the higher heat that would be emitted by the higher wattage bulb. For example, if cause a fire if close to anything combustible. It could also overheat and cause it to fail sooner than it would otherwise. It will also draw more current, but that is a factor in the wiring and any circuit protection. If you are using Compact Fluorescent Bulbs there probably wouldn't be a problem.
Add your answer:
Earn +20 pts
How do you release dome from light fixture in ceiling fan?
Disconnect the fixture wires and remove the central mounting nut to release the dome from the light fixture in a ceiling fan.
How do you wire a 220 volts light?
The light is wired the same as any voltage fixture. Bring the source voltage to the fixture and connect it to the two fixture wires. If you want to control the off-on of the fixture take the source voltage to a switch first and then out of the switch to the light fixture.
Outside porch lamp has no box just two wires coming in black wires are tied and don't connect to fixture just the white wires what is going on here?
It sounds like the black wires may be hot wires coming from the power source and the white wires could be neutral wires. The black wires are typically connected to the fixture's black wires. If the black wires aren't connected and capped off, the fixture won't receive power. It's important to properly connect all wires to ensure the fixture functions safely.
What if the new light fixture has 2 black wires and no white wire?
If the new light fixture has 2 black wires and no white wire, it likely means that the fixture is designed to be connected to a circuit where the white wire has been designated as the hot wire instead of the black wire. Make sure to double check the wiring and consult a professional if you are unsure.
How do you remove a light fixture but leave the wires behind?
Turn off the power to the light fixture at the breaker. Unscrew the fixture from the ceiling, disconnect the wires, and secure the wire ends with wire nuts. Cover the exposed wires with a wire nut and electrical tape to prevent accidents while leaving the wires behind.
What if the light fixture has two copper house wires?
If you mean 2 bare copper wires those are the ground wires. Tie them together and then connect the light fixture ground wire which will be green or bare copper to those ground wires.
How do you release dome from light fixture in ceiling fan?
Disconnect the fixture wires and remove the central mounting nut to release the dome from the light fixture in a ceiling fan.
What do you do with extra wires to a light fixture?
Extra wires to a light fixture are dangerous. It can cause electrical shock when having contact to people therefore it must be guarded to avoid physical contact.
Can a rear parking light fixture be replaced without replacing the rear bumper?
yes it can!! go under your car to wear you see the wires to the light and undo the wires and take the light out then put and wire a new light fixture
How do you wire a 220 volts light?
The light is wired the same as any voltage fixture. Bring the source voltage to the fixture and connect it to the two fixture wires. If you want to control the off-on of the fixture take the source voltage to a switch first and then out of the switch to the light fixture.
Can you run power from a light fixture to another light fixture?
Yes. Connect Black to Black, White to White and bare ground wires together.
How do you wire a fixture that had two hot and two neutral wires?
To install a new fixture to replace the one that was removed reconnect the two hot wires together and then reconnect the two neutral wires together. Place the two wires from the new fixture to the corresponding wire colours that you just spliced together. This wiring should be down stream from the light switch. When the switch is turned on the new fixture should light. If this is not the scenario of your question then more information needs to be given.
Outside porch lamp has no box just two wires coming in black wires are tied and don't connect to fixture just the white wires what is going on here?
It sounds like the black wires may be hot wires coming from the power source and the white wires could be neutral wires. The black wires are typically connected to the fixture's black wires. If the black wires aren't connected and capped off, the fixture won't receive power. It's important to properly connect all wires to ensure the fixture functions safely.
How do you change a tail light bulb holder for a 1994 Pontiac grand am?
Cut the wires on the old fixture and splice wires from new receptacle
How to Hang a Ceiling Light Fixture?
How to Hang a Ceiling Light FixtureA new light fixture is a great way to update a room. Follow these steps to remove the old fixture and install the new one safely and properly.Turn of the power at the circuit breaker panel and make sure the light switch is off as well. Remove the light cover and bulb. Use a screwdriver to remove the screws holding the old fixture in place. Ensure the power is off by using a circuit tester. Remove the wire nuts from the black, white and green wires. These are the hot, neutral and ground wires respectively. Untwist the wires and remove the old light fixture. Make a support bracket to hold the new fixture in place from two "S" hooks and some wire. Make a loop at each end of the wire, slip an "S" hook through each loop. Connect one hook to the light support bracket and the other end to the new light fixture. Twist the black wires together, followed by the white wires and then the green ones. Remove the wire support that you made and gently push the wires back inside the fixture's electrical junction box. Use a screwdriver and screws to attach the new fixture to the mounting bracket. Screw in the light bulbs. Compact fluorescent bulbs are an environmentally friendly option. Attach the light cover. Turn on the power and test the light.
Troubleshooting 40 year old outside wiring to light fixture?
Yes
What if the new light fixture has 2 black wires and no white wire?
If the new light fixture has 2 black wires and no white wire, it likely means that the fixture is designed to be connected to a circuit where the white wire has been designated as the hot wire instead of the black wire. Make sure to double check the wiring and consult a professional if you are unsure.
