0
What else can I help you with?
What is larger 6 AWG or 4 AWG?
4 Gauge wire is larger in diameter than 6 Gauge wire.
What is the difference between 10 awg and 12 awg speaker wire?
10 AWG wire will have less resistance per foot and therefore you can have longer runs with 10 AWG than 12 AWG without as much loss of signal. Additional to loss of signal there is a need to maintain a low impedance driving the typical speaker with its 4 ohm or 8 ohm coil resistance, to avoid frequency-distortion. A guide rule is that the speaker cable should have a total resistance around 1% of the speaker resistance (or less). On that basis, for 5 yards of speaker cable for a 4 ohm speaker the wire size would be 4 sq. mm (11 AWG) or for an 8 ohm speaker 2 sq. mm (14 AWG). <<>> Using the above formula of 1% of the speaker resistance the above answer is not correct. For a 4 ohm speaker at 1% is .04 ohms. The resistance of #12 wire is .001588 ohms per foot. This will allow you to run 25 feet and still stay within the parameters. For a 4 ohm speaker at 1% is .04 ohms. The resistance of #10 wire is .00100 ohms per foot. This will allow you to run 40 feet and still stay within the parameters. You can see, what the first answer states is correct.
What size wire for electric cook top?
AWG # 6 copper or AWG # 4 aluminum
What size wire to use for 100 amp service 160 feet from the power pole?
For a 100 amp service located 160 feet from the power pole, it is recommended to use 2 AWG copper wire or 1/0 AWG aluminum wire to ensure proper voltage drop and safety. Be sure to consult with a licensed electrician to determine the specific requirements for your installation.
Can you use 4 AWG wire with a 6 AWG ground wire to a sub box 100 feet away?
Yes you can. You did not say how many amps were required.
Which has more power 4 AWG or 18 AWG?
Power is the product of amps x volts, it has nothing to do with wire size.
What is larger 6 AWG or 4 AWG?
4 Gauge wire is larger in diameter than 6 Gauge wire.
What is the recommended gauge for 18/4 thermostat wire in a residential HVAC system?
The recommended gauge for 18/4 thermostat wire in a residential HVAC system is typically 18 AWG (American Wire Gauge).
What is the difference between -18 and -4?
-14
Find the difference -18-4?
-14
What is the difference between 18 and -4?
Using the number line Start at '18' and move to the left, until you reach '-4' . You have made '22' steps ; the difference. Arithmetically 18 - - 4 = 18 + 4 = 22 The difference. Note the double negative.
What is the difference between 10 awg and 12 awg speaker wire?
10 AWG wire will have less resistance per foot and therefore you can have longer runs with 10 AWG than 12 AWG without as much loss of signal. Additional to loss of signal there is a need to maintain a low impedance driving the typical speaker with its 4 ohm or 8 ohm coil resistance, to avoid frequency-distortion. A guide rule is that the speaker cable should have a total resistance around 1% of the speaker resistance (or less). On that basis, for 5 yards of speaker cable for a 4 ohm speaker the wire size would be 4 sq. mm (11 AWG) or for an 8 ohm speaker 2 sq. mm (14 AWG). <<>> Using the above formula of 1% of the speaker resistance the above answer is not correct. For a 4 ohm speaker at 1% is .04 ohms. The resistance of #12 wire is .001588 ohms per foot. This will allow you to run 25 feet and still stay within the parameters. For a 4 ohm speaker at 1% is .04 ohms. The resistance of #10 wire is .00100 ohms per foot. This will allow you to run 40 feet and still stay within the parameters. You can see, what the first answer states is correct.
Splice 5 12 AWG wires into 1 4 AWG wire?
No, code does not allow that.
What size wire for electric cook top?
AWG # 6 copper or AWG # 4 aluminum
What is the base of 18 to the 4th power?
Base = 18, Power = 4
What size wire to use for 100 amp service 160 feet from the power pole?
For a 100 amp service located 160 feet from the power pole, it is recommended to use 2 AWG copper wire or 1/0 AWG aluminum wire to ensure proper voltage drop and safety. Be sure to consult with a licensed electrician to determine the specific requirements for your installation.
What is the difference between Analytics and analysis?
18+4
