0
Assuming its copper. Number #3 or #2 is fine
Wiki User
∙ 12y ago
For a 100 amp service at 75 feet, you would typically use 2 AWG copper wire or 1/0 AWG aluminum wire. Make sure to consult the National Electrical Code (NEC) and local regulations to ensure compliance with standards and safety requirements. Consider factors like voltage drop and insulation type when selecting the appropriate wire size.
Add your answer:
Earn +20 pts
What size wire do you use for up to 350 feet for 100 amp service?
That can't be answered until you state the voltage.
What size feeder wire for 100 amps?
For a 100 amp service, a common feeder wire size would be 2 AWG (American Wire Gauge) copper or 1/0 AWG aluminum. These sizes are appropriate for handling the current capacity needed for a 100 amp electrical service. It is important to consult with a licensed electrician or local building code requirements to ensure the proper wire size for your specific installation.
What size wire to use for 100 amp service 160 feet from the power pole?
For a 100 amp service located 160 feet from the power pole, it is recommended to use 2 AWG copper wire or 1/0 AWG aluminum wire to ensure proper voltage drop and safety. Be sure to consult with a licensed electrician to determine the specific requirements for your installation.
What size wire is required to run 100 amp service 100 yards?
I would recommend you use AWG # 2 copper or AWG # 1/0 aluminum for that distance and amperage.
What size wire needed for 100 amp service 700 feet away?
For a 100 amp service 700 feet away, you would typically use 3/0 AWG aluminum wire to account for the voltage drop over that distance. It is important to consult with a licensed electrician or local building codes to determine the exact specifications required for your specific situation.
What size wire to use for 100 amp service 160 feet from the power pole?
For a 100 amp service located 160 feet from the power pole, it is recommended to use 2 AWG copper wire or 1/0 AWG aluminum wire to ensure proper voltage drop and safety. Be sure to consult with a licensed electrician to determine the specific requirements for your installation.
What size wire do you use for up to 350 feet for 100 amp service?
That can't be answered until you state the voltage.
What size ground wire for 100a service?
A 100 amp residential service requires a size #8 copper wire, it should be insulated in green.
What size wire for a 200 amp 3phase service 100 feet away?
This is a voltage drop question. A voltage must be stated to answer this question.
What is the required wire size for 100?
A 100 amp service requires that you use AWG 4 copper wire or AWG 2 aluminum wire.
What wire size for 100 amp single phase 3 wire commercial service?
2 copper
What size wire do you need for 100 amp service if you use alunimum?
2AWG.
What size feeder wire for 100 amps?
For a 100 amp service, a common feeder wire size would be 2 AWG (American Wire Gauge) copper or 1/0 AWG aluminum. These sizes are appropriate for handling the current capacity needed for a 100 amp electrical service. It is important to consult with a licensed electrician or local building code requirements to ensure the proper wire size for your specific installation.
What size service cable for 100 amp main panel 100 feet away?
For a 100 amp main panel located 100 feet away, it is recommended to use a 2/0 copper or 4/0 aluminum service cable to ensure proper voltage drop and capacity for the distance. Consult with a licensed electrician to determine the specific requirements based on local codes and conditions.
What gauge wire required to go 50 feet for a 100 amp service?
AWG # 4 copper.
What size aluminum wire for 100 amps undergroundservice 60 feet from meter?
A 3/0 aluminum conductor will limit the voltage drop to 3% or less when supplying 150 amps for 150 feet on a 240 volt system. This size will allow the conductor to be loaded to 120 amps. 150 x 80% = 120 Conductors are only allowed to be loaded to 80% or their rated capacity. If you need the full 150 amps then you would need to use a wire with a rating of 190 amps. 190 x 80% = 152 amps A 4/0 aluminum conductor will limit the voltage drop to 3% or less when supplying 190 amps for 150 feet on a 240 volt system.
What size aluminum wire for 1200 amp service?
For Service Entrance Cable 600 kcmill (Thousands of circular mils).
