0
Add your answer:
Earn +20 pts
How big of breaker do you use for 115 volt?
Depends on the wire size used in the circuit. If you use AWG # 14 wire you must use a 15 amp breaker. If it is wired with AWG # 12 wire then you use a 20 amp breaker. If a AWG # 10 wire is used then a 30 amp breaker is required. The breaker protects the wiring from overheating so you must use the proper size breaker for the wire used.
What size breaker should be used for a TNIA-10 wire?
The breaker size for a TNIA-10 wire depends on the maximum current carrying capacity of the wire, which is typically indicated on the wire's packaging or in its specifications sheet. You should select a breaker that is rated slightly higher than the wire's maximum current capacity to ensure safety and avoid overloading the wire. It is recommended to consult with a qualified electrician for specific guidance on breaker sizing for your installation.
Can you put 20amp breaker on 10-2 wire?
No, you should match the breaker size to the wire gauge. A 10-2 wire is typically rated for a 30 amp breaker. Using a 20 amp breaker on 10-2 wire could result in overheating and a potential fire hazard.
What is the minimum wire size for a 30Amp breaker?
The minimum wire size for a 30Amp breaker is typically 10 AWG for copper wire and 8 AWG for aluminum wire, according to the National Electrical Code (NEC). This wire size is necessary to safely carry the amount of current without overheating.
Can 10 gauge wire be used on a 20 amp breaker?
No, it is not recommended. A 20 amp breaker should be used with a wire gauge of 12 or smaller to ensure the wire does not overheat and cause a fire hazard. Using a 10 gauge wire on a 20 amp breaker could potentially overload the wire and overheated it.
How big of breaker do you use for 115 volt?
Depends on the wire size used in the circuit. If you use AWG # 14 wire you must use a 15 amp breaker. If it is wired with AWG # 12 wire then you use a 20 amp breaker. If a AWG # 10 wire is used then a 30 amp breaker is required. The breaker protects the wiring from overheating so you must use the proper size breaker for the wire used.
What size circut breaker for 10-2 wire?
A #10 wire has the capacity for 30 amps. No breaker larger than 30 amps should be used to protect the circuit.
What size breaker should be used on a 20 amp motor?
30 amp breaker with #10 gauge copper wire
What size breaker should be used for a TNIA-10 wire?
The breaker size for a TNIA-10 wire depends on the maximum current carrying capacity of the wire, which is typically indicated on the wire's packaging or in its specifications sheet. You should select a breaker that is rated slightly higher than the wire's maximum current capacity to ensure safety and avoid overloading the wire. It is recommended to consult with a qualified electrician for specific guidance on breaker sizing for your installation.
What size wire would you use on a 30amp breaker?
AWG # 10 wire.
What size breaker should you use for a tnia-10 wire?
25 amp breaker
What size breaker does it take to run a outdoor well?
Normally AWG #10 wire on a 30 amp breaker but it really depends on the size of the pump. The pump manufacture will specify the size wire and size breaker needed.
Should 25 amps breaker be replaced by 20 amps?
For typical residential house wiring 12 AWG wire is required for a 20 Amp breaker. If you change out the breaker for a 25 A breaker you would have to rewire the circuit with 10 AWG. In that case you could up the breaker to 30 Amps. All outlets and switches should be rated at the same voltage and current as the breaker.
Can you put 20amp breaker on 10-2 wire?
No, you should match the breaker size to the wire gauge. A 10-2 wire is typically rated for a 30 amp breaker. Using a 20 amp breaker on 10-2 wire could result in overheating and a potential fire hazard.
What is the minimum wire size for a 30Amp breaker?
The minimum wire size for a 30Amp breaker is typically 10 AWG for copper wire and 8 AWG for aluminum wire, according to the National Electrical Code (NEC). This wire size is necessary to safely carry the amount of current without overheating.
Can 10 gauge wire be used on a 20 amp breaker?
No, it is not recommended. A 20 amp breaker should be used with a wire gauge of 12 or smaller to ensure the wire does not overheat and cause a fire hazard. Using a 10 gauge wire on a 20 amp breaker could potentially overload the wire and overheated it.
What size wire is required for 120v 5amp 250ft?
Use AWG #10 wire on a 20 amp breaker.
