0
What else can I help you with?
What size breaker for 120 volt 2500 watt water heater?
For a 2500 watt water heater operating at 120 volts, you would need a 20 amp breaker. This ensures the breaker can handle the load without tripping.
What is breaker size for 240 volt 9 KW?
The formula you are looking for is I = W/E.
A range name plate says 78 amps what size breaker needed?
To determine the size of the breaker needed for a 78 amp range, you typically need to use a breaker that is the next size up from the amp rating. This means that you would need an 80 amp breaker to safely accommodate the 78 amp range. However, always consult with a qualified electrician to ensure the correct breaker size for your specific electrical setup.
What is type of breaker for 41 amp's?
For a 41 amp load, you would typically use a 50 amp circuit breaker. The general rule is to select a breaker size that is 125% of the continuous load amps or equal to the load amps if it is not a continuous load. In this case, 41 amps is considered a continuous load, so you would round up to the nearest available breaker size, which is 50 amps.
Can you put a 20amp water pump and a 30 amp water heater on a 50amp breaker?
No, it is not safe to put a 20 amp water pump and a 30 amp water heater on a 50 amp breaker. The total amperage exceeds the capacity of the breaker, which can lead to overheating, tripping, or even a fire hazard. It is recommended to have separate dedicated circuits for each appliance to ensure safety and proper functionality.
What are the standard size circuit breaker amperages?
In North America the standard sizes for breakers are 15, 20, 30, and 40 amps. The 15 amp size breaker is used in general circuit wiring. The 20 amp size breaker is used for dedicated appliance receptacles, hot water tank and baseboard heating. The 30 amp size breaker is used for a clothes dryer. The 40 amp size breaker is used for the electric range.
What size amp circuit breaker should be used for a hot water tank?
Assuming you are referring to a 240 volt residential hot water heater you will need to install 10/2 NM cable (Romex) with ground from the service panel to the water heater wired to a 30 amp circuit breaker in the service panel. If you cannot see the water heater from the service panel you will need to install a service disconnect at the water heater.
What size breaker do you need for a 40 gallon electric water heater?
Usually 30 amp
Can I replace a 15 amp breaker with a 20 amp breaker?
No, you should not replace a 15 amp breaker with a 20 amp breaker without consulting a licensed electrician. The breaker size should match the wire size to prevent overheating and potential fire hazards.
What size breaker can you use on a 7500watt generator?
Depends on the wire size you are using. If the generator breaker is a 30 amp then install a 30 amp breaker.
What size wire do I need for a 30 amp breaker?
For a 30 amp breaker, you will need a wire that is at least 10 gauge in size.
What is the recommended wire size for a 20 amp breaker?
The recommended wire size for a 20 amp breaker is typically 12-gauge wire.
What is the appropriate wire size for a 25 amp breaker?
The appropriate wire size for a 25 amp breaker is typically 10 gauge wire.
What is the appropriate wire size for a 30 amp breaker?
The appropriate wire size for a 30 amp breaker is typically 10 gauge wire.
What is the recommended wire size for a 25 amp breaker?
The recommended wire size for a 25 amp breaker is typically 10 gauge wire.
What is the recommended wire size for a 30 amp breaker?
The recommended wire size for a 30 amp breaker is typically 10 gauge wire.
What is the recommended wire size for a 50 amp breaker?
The recommended wire size for a 50 amp breaker is typically 6-gauge wire.
