answersLogoWhite

0

Depends upon how far you plan to go with it and what the ordinary operating current of the machine is.

The further away you are, the more resistance there is in the wires and the bigger the wire must be, to avoid damaging the welder with a voltage reduced by the resistance.

For instance, a 240-v 48-A appliance would only get 228 volts at the end of 100 feet of #10 AWG wire because it loses power due to the resistance of the wire.

If you want to go more than 100 feet, you would need larger wires. For 260 feet you would need #6 AWG if you want no more than a 5 percent voltage drop.

<<>>

The amperage that you are looking at is probably the secondary output. Go to the nameplate of the welding machine and look for the input voltage and amperage. Most industrial machines usually take about a 30 amp outlet for the welder to be plugged into. If this is the case then a # 10 cab-tire flexible cable will fit the bill. If it is 48 amps on the input then as suggested above a #6 conductor will handle up to 65 amps.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Natural Sciences

Is my 40 amp breaker and number 8 wire ok for my 220 volt stick welder safe?

Yes, a 40 amp breaker and number 8 wire are generally suitable for a 220-volt stick welder, as they can handle the current typically drawn by such equipment. However, it's crucial to check the welder's specifications to ensure it doesn't exceed the breaker's rating. Additionally, ensure that all connections are secure and that the wiring is installed according to local electrical codes for safety. If in doubt, consulting a licensed electrician is advisable.


How many amps does a 220 volt welder draw?

To determine the amperage drawn by a 220-volt welder, you can use the formula: Amps = Watts / Volts. For example, if the welder is rated at 5,000 watts, it would draw approximately 22.73 amps (5,000 watts / 220 volts). The actual amperage may vary based on the welder's specifications and settings. Always refer to the manufacturer's guidelines for precise information.


What must be checked before using the 110-volt power plug on a portable welder?

Before using the 110-volt power plug on a portable welder, you should check if the plug is compatible with the power outlet, ensure the wiring is in good condition and properly connected, and verify that the welder's power requirements do not exceed the capacity of the power source.


How can you connect a welder to a dryer receptacle?

First you need to know that an electric dryer is almost always a 30 amp 220 Volt power supply. Most small welders require a 50 amp 220 volt power supply. Check your welder's power requirement. If it requires 50 amps, it'll never work correctly on 30 amp.The plug conversion is simple. The wire your dryer is powered by will have two "hot" legs, the red and black wires. These supply the 220 volt. Then it has a ground (bare copper or green conductor. And last it has a white wire, the neutral.Your 3 prong plug on your welder only requires the two "hot" legs and the ground wire. You shunt the neutral white wire with a wire nut.


What is the fundamental quantity of electricity indicating the ability to do work of forcing electrons to move?

The Electron Volt. Its the energy required to move one electron through a Potential Difference of one Volt. Commonly used to decribe size of particle accelerators 1 GeV , one Giga electron Volt , 1 X1012 electron Volts.

Related Questions

Is my 40 amp breaker and number 8 wire ok for my 220 volt stick welder safe?

Yes, a 40 amp breaker and number 8 wire are generally suitable for a 220-volt stick welder, as they can handle the current typically drawn by such equipment. However, it's crucial to check the welder's specifications to ensure it doesn't exceed the breaker's rating. Additionally, ensure that all connections are secure and that the wiring is installed according to local electrical codes for safety. If in doubt, consulting a licensed electrician is advisable.


What size service should you tie a 216 volt mig welder into?

A 216-volt MIG welder typically requires a dedicated circuit with sufficient amperage to handle its power needs. Generally, a 40- to 50-amp service is recommended, depending on the welder's specific requirements. Ensure that the circuit is equipped with the appropriate breaker and wiring gauge to safely support the welder's load. Always consult the manufacturer's specifications and local electrical codes for precise requirements.


Can you run a 220 volt welder on a 20 amp breaker?

Yes, you can run a 220-volt welder on a 20-amp breaker, but it depends on the welder's amperage requirements. If the welder draws more than 20 amps, it could trip the breaker or damage the welder. It's essential to check the welder's specifications and ensure that the circuit can handle the load safely. If the welder requires higher amperage, a breaker with a higher rating may be necessary.


How many amps does a 220 volt welder draw?

To determine the amperage drawn by a 220-volt welder, you can use the formula: Amps = Watts / Volts. For example, if the welder is rated at 5,000 watts, it would draw approximately 22.73 amps (5,000 watts / 220 volts). The actual amperage may vary based on the welder's specifications and settings. Always refer to the manufacturer's guidelines for precise information.


What is the 60 Hz on a welder with the listed input as 208 230 volt single phase 60Hz?

60 Hertz is the frequency that the welder should be connected to, to work as it is designed to.


What is the required wire size for a 230 feet run 480 volt 100 amp?

Depends on length. The more length, the more resistance.


What is the recommended wire size for a 220 volt circuit according to the 220 volt wire size chart?

The recommended wire size for a 220 volt circuit according to the 220 volt wire size chart is typically 10 gauge wire for a circuit with a maximum of 30 amps.


What size maximum level of primary-only overcurrent protection is required for a 600-volt transformer with a primary current rating of 54 amperes?

100


What must be checked before using the 110-volt power plug on a portable welder?

Before using the 110-volt power plug on a portable welder, you should check if the plug is compatible with the power outlet, ensure the wiring is in good condition and properly connected, and verify that the welder's power requirements do not exceed the capacity of the power source.


What size wire is required for 277 volt fluorescent lighting?

Wire size is governed by amperage not voltage. Voltage is an insulation factor when talking about wire. Add up the amperage of fixtures you want in the circuit. Once that is found then the size of the wire can be calculated.


How can you connect a welder to a dryer receptacle?

First you need to know that an electric dryer is almost always a 30 amp 220 Volt power supply. Most small welders require a 50 amp 220 volt power supply. Check your welder's power requirement. If it requires 50 amps, it'll never work correctly on 30 amp.The plug conversion is simple. The wire your dryer is powered by will have two "hot" legs, the red and black wires. These supply the 220 volt. Then it has a ground (bare copper or green conductor. And last it has a white wire, the neutral.Your 3 prong plug on your welder only requires the two "hot" legs and the ground wire. You shunt the neutral white wire with a wire nut.


What is the fundamental quantity of electricity indicating the ability to do work of forcing electrons to move?

The Electron Volt. Its the energy required to move one electron through a Potential Difference of one Volt. Commonly used to decribe size of particle accelerators 1 GeV , one Giga electron Volt , 1 X1012 electron Volts.