0
What else can I help you with?
How many amps does a device need?
The amps required for a device depend on its power consumption. You can calculate the amps by dividing the power rating (in watts) by the voltage (in volts) of the device. For example, a 1200 watt device plugged into a 120-volt outlet would require 10 amps (1200 watts / 120 volts = 10 amps).
How many amps for 115 watts?
To calculate the amps for 115 watts, you need to know the voltage the appliance is operating at. If the appliance is operating at 120 volts, then the current would be approximately 0.96 amps (115 watts / 120 volts).
How many amps do you need for 580 watt?
A very basic formula is that power (watts) equals amperage times voltage. For example, if you are operating at 120 volts, 580 watts, the amperage would be 4.8 amps (580 divided by 120).
How many amps-hour are needed for 600 rpm?
To determine the amp-hours needed for 600 RPM, you need to know the specific power requirements of the device or motor operating at that speed, as well as the voltage. Amp-hours (Ah) is calculated by multiplying current (in amps) by the time (in hours) the device operates. Without additional details regarding the motor's power rating and voltage, it's not possible to provide a specific answer.
How much power does a device that operates on 12 volts and draws 7 amps consume?
The device consumes 84 watts of power. This can be calculated by multiplying the voltage (12 volts) by the current (7 amps). So, 12 volts x 7 amps = 84 watts.
What is the maximum power consumption in watts for a device that operates at 30 amps?
The maximum power consumption for a device operating at 30 amps is 360 watts.
What is the device for amps?
An electrical device may draw amps, but there is not a device that equates to amps. Amperes are the measure of current flow in a circuit.
How many amps does a device need?
The amps required for a device depend on its power consumption. You can calculate the amps by dividing the power rating (in watts) by the voltage (in volts) of the device. For example, a 1200 watt device plugged into a 120-volt outlet would require 10 amps (1200 watts / 120 volts = 10 amps).
How many amps will be used in an air conditioner operating on 240 volts and rated at 1.5 kw?
Depends on power factor, but it should be about 8 Amps.
What is the range of amps supported by this electrical device?
The electrical device supports an amp range of 0 to 10 amps.
What is the maximum current rating for the circuit breaker required for a device that operates at 20 amps?
The maximum current rating for the circuit breaker needed for a device that operates at 20 amps is 25 amps.
What would full load amps be on a 480volt 3 phase 90 kw electric heater be pulling 36 amps per leg?
46 amps
How calculate ups battery backup time?
The UPS should be rated in Amps per Hour. Just divide that number by the current requirements of the device connected to the UPS. Say that the UPS is rated for 10 Ampere Hours and your device draws 2 amps. You could run the device for about 5 hours.
How many amps for 115 watts?
To calculate the amps for 115 watts, you need to know the voltage the appliance is operating at. If the appliance is operating at 120 volts, then the current would be approximately 0.96 amps (115 watts / 120 volts).
What is the maximum amperage requirement for operating the oven?
The maximum amperage requirement for operating the oven is 20 amps.
How many watts in a 115 volt refrigerator?
How many Amps is the fridge pulling? Multiply the Amps by the 120V circuit you're plugging into and you'll get your Watts.
How many amps do you need for 580 watt?
A very basic formula is that power (watts) equals amperage times voltage. For example, if you are operating at 120 volts, 580 watts, the amperage would be 4.8 amps (580 divided by 120).
