0
What else can I help you with?
Can you use a double 30amp breaker to feed 2 15 amp?
no, load will brake at 30 not 15 as needed
Can you charge 230 volts appliances with 130 volts?
No, you will need to obtain an adapter to change the 120 volts to 230 volts. The adapter must be sized to the load wattage of the 230 volt appliance. To find the load wattage multiply the amperage times the voltage of the appliance. Once this is assessed, the size of the adapter or transformer will be of equal or greater value than that of the connected appliance. The adapter will be rated in VA or KVA depending on the needed load amperage.
How many amps in 40 kva?
To calculate the amperage of a 40 kVA load, you will need to know the voltage. The formula is: Amps = kVA / Volts. Assuming a standard line voltage of 120V, the amperage for a 40 kVA load would be approximately 333 amps.
What size wire needed for 25 amps 220 volts for 75 feet?
For a 25 amp load at 220 volts over a distance of 75 feet, you will need a 10-gauge wire to ensure safe and efficient electrical conductivity. This wire size allows for minimal voltage drop and meets the necessary ampacity requirements for the circuit. Make sure to consult local electrical codes and regulations before installation.
What size wire needed with a 100 amp load 250 feet away?
To determine the wire size needed for a 100 amp load 250 feet away, you will need to consider the voltage and allow for voltage drop. For a 100 amp load at 120V over 250 feet, you would need a wire size of at least 1/0 AWG. It's recommended to consult with a licensed electrician to ensure proper wire size for your specific situation.
Can you use a double 30amp breaker to feed 2 15 amp?
no, load will brake at 30 not 15 as needed
What size resistor needed to drop 3 volts dc to 2.5 volts dc?
You will need to take the resistance of the load into account if you are going to design a voltage divider. The resistance of the load can completely change the voltage ratio of a voltage divider if not factored into the calculation. you can measure or read R(load), then R(needed) = 0.8 R(load)
What size resistor is needed to drop 14 volts dc to 12 volts dc?
This question cannot be answered because you did not specify the current.
Can you charge 230 volts appliances with 130 volts?
No, you will need to obtain an adapter to change the 120 volts to 230 volts. The adapter must be sized to the load wattage of the 230 volt appliance. To find the load wattage multiply the amperage times the voltage of the appliance. Once this is assessed, the size of the adapter or transformer will be of equal or greater value than that of the connected appliance. The adapter will be rated in VA or KVA depending on the needed load amperage.
What do you have to do to run 110 volts 1500 feet in length and still have the 110 volt power at the end of the line?
To answer this voltage drop question another componant is needed. The wire can be sized to maintain the voltage to a less that 3% loss but what is needed is the current of the load at the far end of the line. Without this amperage this answer can not be answered.
What is the full load amps for 2.4 hp motor at 460 volts?
what is the full load amps for 2.4 hp motor at 460 volts ?
How many amps in 40 kva?
To calculate the amperage of a 40 kVA load, you will need to know the voltage. The formula is: Amps = kVA / Volts. Assuming a standard line voltage of 120V, the amperage for a 40 kVA load would be approximately 333 amps.
If the potential difference across a load is 60 volts and the resistance of the load is 10 ohms the current is amperes.?
It's not that simple. The basic formula is Volts / Ohms = Amps. For 30 Volts you'd get 0.5 Amps, for 60 Volts you'd get 1 Amp, for 120 Volts you'd get 2 Amps.
What size wire needed for 25 amps 220 volts for 75 feet?
For a 25 amp load at 220 volts over a distance of 75 feet, you will need a 10-gauge wire to ensure safe and efficient electrical conductivity. This wire size allows for minimal voltage drop and meets the necessary ampacity requirements for the circuit. Make sure to consult local electrical codes and regulations before installation.
How do volts get power?
Volts cause current to flow through the load. The current is measured in amps, and the volts multiplied by the amps gives the power in watts.
A 240 volt single phase circuit has a resistive load of 8500 what is the net calculated current to supply this load?
Ohm's law: Volts = Amps * Ohms, or Amps = Volts / Ohms 240 volts / 8500 ohms = 28 milliamps
What size wire needed with a 100 amp load 250 feet away?
To determine the wire size needed for a 100 amp load 250 feet away, you will need to consider the voltage and allow for voltage drop. For a 100 amp load at 120V over 250 feet, you would need a wire size of at least 1/0 AWG. It's recommended to consult with a licensed electrician to ensure proper wire size for your specific situation.
