at your local hardware store go to the electrical dept, not the normal but the contractors area and you should find a 240v circuit breakers, fuses, junctions, wires and anything else you can think of!
TucsonDirect
Buy a 3 wire cord for your dryer.
If you need a 220v circuit at only 15 or 20 amps: Get a new breaker to replace your 110v single pole breaker with a 220v double pole breaker. (You cannot exceed the original breaker's amperage rating unless you also replace the wire with a larger size). Shut off the panel's main breaker (the wires coming into the main breaker will remain hot, so don't touch them.) Remove the old 110v circuit's neutral (white) from the neutral bus bar in your distribution panel. Remove the old 110v circuit's hot (black) from the old 110v breaker. Remove the old 110v breaker. Install the new 220v breaker in place of the old breaker. (This may require you to rearrange some breakers if the old breaker was in between others) Reconnect the black wire to one terminal of the 220v breaker, and reconnect the white wire to the other terminal. Turn on the main breaker, and your new 220v breaker. Before you do this, be sure where the actual circuit goes. Changing 110v to 220v if the circuit is feeding regular 110v receptacles will cause damage to devices plugged into them. Be sure you remove all 110v devices (receptacles) from the circuit before converting it. If you need a 220v circuit for a dryer or other large appliance, your existing wiring will not be sufficient to do the above. You will need to install a new breaker and wiring. For this task, you should consult a professional electrician.
An electrical contractor or electrician would definitely be competent to help with that repair. The handyman laws in some states allow a handyman to perform minor repairs such as replacing a circuit breaker. It's a simple process, you just have to make certain that you shut down the power so nobody gets electrocuted. Replacing a circuit breaker is not a minor repair, NFPA 70E - Standard for Electrical Safety in the Workplace as well as the National Electrical Code state that only a qualified person can do electrical work. A qualified person is "One who has skills and knowledge related to the construction and operation of the electrical equipment and installations and has received safety training to recognize and avoid the hazards involved."
If the breaker trips when nothing is turned on it could be a mouse problem. If it only trips when certain lights or appliances are turned on one of them is probably the reason.If it trips when nothing is being turned on or off something is getting hot. You should then have qualified electrician look at it. Hope this is usefull.
Try checking the connections at the switch and the fan to ensure they are secure. You may also want to use a voltage tester to verify if there is power at the switch. If there is no power at the switch, you may need to check the wiring in the junction box. If everything looks fine, the issue may be with the fan itself and you may need to contact a professional for further assistance.
Buy a 3 wire cord for your dryer.
its a circuit breaker... call the dealer for the parts # or just buy it from them ($40). Try a junk yard or craigslist f150 f250 and bronco about the same year are all the same i think.
Circuit breaker. The circuit breaker should be near the pedals next to the door. It also depends on what kind of car that you have. But usually they are near the pedals by the door. They should be under the dashboard, in a little box. The instructions for them is either givin to you when you buy the car, or they are on the panel door for the circuits and stuff.
If you have Circuit Breaker Buyers, finding the right buyer is noteworthy. Double-D-Circuitbreakers interface you with the best circuit breaker buyers, guaranteeing you get the most great deal. With a long experience within the industry, Double-D-Circuitbreakers is your go-to assistant for selling electrical equipment quickly and beneficially. Circuit breakers are fundamental components in electrical systems, but they can collect as flood amid updates or decommissioning ventures. Selling your unused circuit breakers may be a sharp money-related move. Here's why Circuit Breaker Buyers can be turned into cash. Instead of letting them sit unused, selling them to a dependable buyer can provide provoke financial returns. Unused equipment takes up beneficial space.
If you need a 220v circuit at only 15 or 20 amps: Get a new breaker to replace your 110v single pole breaker with a 220v double pole breaker. (You cannot exceed the original breaker's amperage rating unless you also replace the wire with a larger size). Shut off the panel's main breaker (the wires coming into the main breaker will remain hot, so don't touch them.) Remove the old 110v circuit's neutral (white) from the neutral bus bar in your distribution panel. Remove the old 110v circuit's hot (black) from the old 110v breaker. Remove the old 110v breaker. Install the new 220v breaker in place of the old breaker. (This may require you to rearrange some breakers if the old breaker was in between others) Reconnect the black wire to one terminal of the 220v breaker, and reconnect the white wire to the other terminal. Turn on the main breaker, and your new 220v breaker. Before you do this, be sure where the actual circuit goes. Changing 110v to 220v if the circuit is feeding regular 110v receptacles will cause damage to devices plugged into them. Be sure you remove all 110v devices (receptacles) from the circuit before converting it. If you need a 220v circuit for a dryer or other large appliance, your existing wiring will not be sufficient to do the above. You will need to install a new breaker and wiring. For this task, you should consult a professional electrician.
IMO it would be because the circuit breaker has the possibility of going bad and not working (allowing a short to move through the device), but fuses blow (cause a break) no matter what if shorted.
The only place I remember a self reseting circuit breaker on my 67 is the line the feeds the power convertible top. But in general, most parts stores have circuit breakers like that, you simply need to know how large (how many amps) you want to buy.
An electrical contractor or electrician would definitely be competent to help with that repair. The handyman laws in some states allow a handyman to perform minor repairs such as replacing a circuit breaker. It's a simple process, you just have to make certain that you shut down the power so nobody gets electrocuted. Replacing a circuit breaker is not a minor repair, NFPA 70E - Standard for Electrical Safety in the Workplace as well as the National Electrical Code state that only a qualified person can do electrical work. A qualified person is "One who has skills and knowledge related to the construction and operation of the electrical equipment and installations and has received safety training to recognize and avoid the hazards involved."
Buy a new one, hire a professional, or look up a DIY guide from a home improvement website, such as HouseLogic.
Advantage: a fuse is guaranteed to pop only when too many amps are pulled, unlike a circuit breaker that may be "accidentally" turned off by some practical joker. Disadvantage: You must have spares on hand (or go buy them when needed) unlike a circuit breaker which can be reset over and over.
If the breaker trips when nothing is turned on it could be a mouse problem. If it only trips when certain lights or appliances are turned on one of them is probably the reason.If it trips when nothing is being turned on or off something is getting hot. You should then have qualified electrician look at it. Hope this is usefull.
You still need a circuit breaker. From your question it appears your stove is hardwired to the panel. It is perfectly acceptable to connect it to a suitably specified outlet and plug for the voltage and amperes for the stove. Basically you would turn off the breaker, install an outlet on the floor or wall so as not to interfere with stove. You can buy cords with the proper plugs and mating receptacles in most any hardware store. For an electric stove with an oven you are usually talking about a 50A breaker and the corresponding outlet and plug. This can be dangerous and if you are not sure of what you are doing an electrician is highly recommended.